ДАТЧИК УРОВНЯ МАСЛА УСТАНОВКА


  1. INSTALL ENGINE OIL LEVEL SENSOR


    1. A01GLUW

      Install a new gasket to the engine oil level sensor.

    2. Insert the engine oil level sensor into the oil pan and rotate it 180°.

    3. A01GIMM

      Install the engine oil level sensor with the 4 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    4. Connect the engine oil level sensor connector.

  2. INSTALL CRANK POSITION SENSOR BRACKET


    1. A01GMY0

      Install the crank position sensor bracket with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Connect the harness clamp.

  3. CONNECT OIL COOLER TUBE


    1. A01GNTA

      Connect the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube by installing the 2 clamps with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  4. ADD ENGINE OIL


    1. Add fresh oil.

      Standard engine oil
      Oil grade Oil Viscosity (SAE)
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      0W-20

      5W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil

      15W-40

      20W-50
      Standard capacity
      Item Specified Condition
      Drain and refill without oil filter change 8.4 liters (8.9 US qts, 7.4 Imp. qts)
      Drain and refill with oil filter change 8.6 liters (9.1 US qts, 7.6 Imp. qts)
      Dry fill 10.2 liters (10.8 US qts, 9.0 Imp. qts)

    2. Install the oil filler cap.

    3. Close the oil filler cap service hole cover.

  5. INSPECT FOR ENGINE OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.

  6. CHECK ENGINE OIL LEVEL


    1. Warm up the engine, stop the engine and wait 5 minutes. The oil level should be between the dipstick's low level mark and full level mark.

      If low, check for leakage and add oil up to the full level mark.

      Note

      Do not fill engine oil above the full level mark.

      Tech Tips

      A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.


      • When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.

      • If low quality oil or oil of an inappropriate viscosity is used.

      • When driving at high engine speed or with a heavy load, (when towing, or), when driving while accelerating or decelerating frequently.

      • When leaving the idling for a long time, or when driving frequently through heavy traffic.

      When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.

  7. INSTALL FRONT SUSPENSION MEMBER PROTECTOR LOWER


    1. Install the front suspension member protector lower with the 8 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  8. INSTALL NO. 2 ENGINE UNDER COVER


    1. A01GNYRE01

      Install the No. 2 engine under cover with the 8 bolts.

      Torque:
      for Bolt A
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      for Bolt B
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

  9. INSTALL NO. 1 ENGINE UNDER COVER


    1. Установите защиту картера двигателя № 1 и закрепите ее 13 винтами и 7 фиксаторами.