ЭЛЕКТРОДВИГАТЕЛЬ МЕХАНИЗМА ИЗМЕНЕНИЯ ФАЗ ГАЗОРАСПРЕДЕЛЕНИЯ УСТАНОВКА


  1. INSTALL CAMSHAFT TIMING CONTROL MOTOR LH


    1. A01GJJ2E01

      Turn the camshaft timing gear assembly's eccentric shaft index slot in the counterclockwise direction by hand, and set it to the maximum retard angle position.

      Tech Tips


      • When the cam of the camshaft lifts the valve, the eccentric shaft becomes difficult to turn.

      • The position where the eccentric shaft stops is the maximum retard angle.

    2. Install a new O-ring to the timing chain cover.

    3. A01GKZOE01

      Align the joint of the camshaft timing control motor LH and the keyway of the camshaft timing gear assembly, and install the motor with the 3 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      Note


      • Check that [L] is printed on the label of the camshaft timing control motor LH.

      • Do not allow foreign matter to contact the oil seal face of the camshaft timing control motor LH (connecting surface with timing chain cover sub-assembly).

      • When installing the camshaft timing control motor LH, do not use excessive force.

      • Align the timing chain cover sub-assembly knock pin with the camshaft timing control motor LH pin hole to install the camshaft timing control motor LH.

      • Install the camshaft timing control motor LH with the arrow facing upward, as shown in the illustration.

      • Do not drop the camshaft timing control motor LH. If dropped, replace it.

      • Do not disassemble the camshaft timing control motor LH. If disassembled, replace it.

    4. A01GI7U

      Connect the 2 camshaft timing control motor LH connectors and engine wire clamp.

  2. INSTALL CAMSHAFT TIMING CONTROL MOTOR RH


    1. A01GK5SE01

      Turn the camshaft timing gear assembly's eccentric shaft index slot in the counterclockwise direction by hand, and set it to the maximum retard angle position.

      Tech Tips


      • When the cam of the camshaft lifts the valve, the eccentric shaft becomes difficult to turn.

      • The position where the eccentric shaft stops is the maximum retard angle.

    2. Install a new O-ring to the timing chain cover.

    3. A01GJK7E01

      Align the joint of the camshaft timing control motor RH and the keyway of the camshaft timing gear assembly, and install the motor with the 3 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

      Note


      • Check that [R] is printed on the label of the camshaft timing control motor RH.

      • Do not allow foreign matter to contact the oil seal face of the camshaft timing control motor RH (connecting surface with timing chain cover sub-assembly).

      • When installing the camshaft timing control motor RH, do not use excessive force.

      • Align the timing chain cover sub-assembly knock pin with the camshaft timing control motor RH pin hole to install the camshaft timing control motor RH.

      • Install the camshaft timing control motor RH with the arrow facing upward, as shown in the illustration.

      • Do not drop the camshaft timing control motor RH. If dropped, replace it.

      • Do not disassemble the camshaft timing control motor RH. If disassembled, replace it.

    4. A01GJ3X

      Install the engine wire bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    5. Connect the 2 camshaft timing control motor RH connectors.

  3. INSTALL INTAKE AIR CONNECTOR PIPE

    Click here

  4. REMOVE COWL TOP VENTILATOR LOUVER RH

    A01GM4S

    1. Расцепите 6 фиксаторов и снимите правую вентиляционную решетку в верхней части кожуха.

  5. PRECAUTION

    Note

    After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here.

  6. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    Tech Tips

    Disconnect the cable from the negative battery terminal so that the maximum retard angle of the camshaft timing control motor will be learned.

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. INSTALL COWL TOP VENTILATOR LOUVER RH


    1. A01GM4S

      Введите в зацепление 6 фиксаторов и установите правую вентиляционную решетку в верхней части кожуха.

      Note

      Если правая вентиляционная решетка в верхней части кожуха установлена ненадлежащим образом, в моторный отсек может проникать вода, что приведет к возникновению неисправностей. Поэтому убедитесь, что правая вентиляционная решетка в верхней части кожуха установлена надлежащим образом.