Click here

СИСТЕМА SFI, Diagnostic DTC:P1362, P1363

Click here
Click here
DTC Code DTC Name
P1362 "B" Camshaft Position Actuator Circuit Open, Low, High Bank1
P1363 "B" Camshaft Position Actuator Circuit Open, Low, High Bank2
Click here

DESCRIPTION

Refer to DTC P0010 (see pageClick here).

DTC No. DTC Detection Condition Trouble Area
P1362

While engine is running, malfunction in rotation direction signal (VTD1) of camshaft timing control motor is detected for 3 seconds

(1 trip detection logic)

  • Camshaft timing control motor (bank 1)

  • Wire harness and connector

  • Camshaft timing control motor power Source
P1363

While engine is running, malfunction in rotation direction signal (VTD2) of camshaft timing control motor is detected for 3 seconds

(1 trip detection logic)

  • Camshaft timing control motor (bank 2)

  • Wire harness and connector
Click here

MONITOR DESCRIPTION

This DTC is output when a rotation direction signal malfunction is detected in the intake side camshaft timing control motor. While the engine is running, if a rotation direction signal (VTD) malfunction is detected, a DTC is output (2 trip detection logic).

When there is a malfunction, if the engine is idled for 30 seconds or the vehicle is driven in an urban area for 5 minutes, a DTC is output.

Click here

WIRING DIAGRAM

Refer to DTC P1360 (see pageClick here).

Click here

INSPECTION PROCEDURE

Tip:

Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

Click here

PROCEDURE


  1. Click here

    INSPECT VVT RELAY (VVT LH, VVT RH)


    1. A01GMJI

      Remove the VVT LH relay or VVT RH relay from the engine room No. 2 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      3 - 5 When no battery voltage applied to terminals 1 and 2 10 kΩ or higher
      3 - 5 When battery voltage applied to terminals 1 and 2 Below 1 Ω

  2. Click here

    CHECK HARNESS AND CONNECTOR (POWER SOURCE VOLTAGE)


    1. A01GIMXE05

      Disconnect the E9 or E19 camshaft timing control motor.

    2. Turn the engine switch on (IG).

    3. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      E9-1 (+B) - Body ground Engine switch on (IG) 11 to 14 V
      E19-1 (+B) - Body ground

  3. Click here

    CHECK HARNESS AND CONNECTOR


    1. A01GIMXE06

      Turn the engine switch off.

    2. Disconnect the E9 or E19 camshaft timing control motor.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      E9-2 (PGND) - Body ground Always Below 1 Ω
      E19-2 (PGND) - Body ground

  4. Click here

    CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING CONTROL MOTOR - ECM)


    1. A01GLR2E34

      Disconnect the E4 or E2 ECM connector.

    2. Disconnect the E10 or E18 camshaft timing control motor connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance (Check for open)
      Tester Connection Condition Specified Condition
      E10-2 (VTD1) - E4-31 (EMF1) Always Below 1 Ω
      E18-2 (VTD2) - E2-30 (EMF2)
      Standard resistance (Check for short)
      Tester Connection Condition Specified Condition
      E10-2 (VTD1) or E4-31 (EMF1) - Body ground Always 10 kΩ or higher
      E18-2 (VTD2) or E2-30 (EMF2) - Body ground

  5. Click here

    REPLACE CAMSHAFT TIMING CONTROL MOTOR (BANK 1 OR BANK 2)


    1. Replace the camshaft timing control motor (see pageClick here).


  6. Click here

    CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester ON.

    4. Clear the DTCs (see pageClick here).

    5. Start the engine and allow the engine idle for 10 seconds or more.

    6. Enter the following menus: Powertrain / Engine / DTC.

    7. Read DTCs.

      Result
      Display (DTC Output) Proceed to
      No DTC A
      Other DTCs B

  7. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. Click here

    END

  9. Click here

    GO TO DTC CHARTClick here

  10. Click here

    REPLACE VVT RELAY (VVT LH, VVT RH)

  11. Click here

    REPLACE HARNESS OR CONNECTOR (VVT RELAY (VVT LH, VVT RH) - CAMSHAFT TIMING MOTOR)

  12. Click here

    INSPECT CAMSHAFT TIMING CONTROL MOTOR (BANK 1 OR BANK 2)


    1. Check that the 3 bolts of the camshaft timing control motor are tightened securely.

      21 N*m 214 kgf*cm 15 ft.*lbf

  13. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR (VVT RELAY (VVT LH, VVT RH) - CAMSHAFT TIMING CONTROL MOTOR)


  14. Click here

    CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester ON.

    4. Clear the DTCs (see pageClick here).

    5. Start the engine and allow the engine idle for 10 seconds or more.

    6. Enter the following menus: Powertrain / Engine / DTC.

    7. Read DTCs.

      Result
      Display (DTC Output) Proceed to
      No DTC A
      Other DTCs B

  15. Click here

    TIGHTEN BOLTClick here