СИСТЕМА SFI, Diagnostic DTC:P0011, P0021

DTC Code DTC Name
P0011 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 1)
P0021 Camshaft Position "A" - Timing Over-Advanced or System Performance (Bank 2)

DESCRIPTION

Refer to DTC P0010 Click here.

DTC No. DTC Detection Condition Trouble Area
P0011

Valve timing on bank 1 intake side remains in advance position, and there is difference target and actual valve timing for approx. 60 seconds or more

(1 trip detection logic)

 Camshaft timing gear assembly (bank 1)
P0021

Valve timing on bank 2 intake side remains in advance position, and there is difference target and actual valve timing for approx. 60 seconds or more

(1 trip detection logic)

 Camshaft timing gear assembly (bank 2)

MONITOR DESCRIPTION

This DTC is output when a valve timing stuck condition is detected. With the engine speed at 4000 rpm or less in the advance angle position, if the valve timing does not vary, or a large difference in the target and actual valve timing occurs continuously for 5 seconds, it is determined that a malfunction has occurred. When this malfunction is detected, a DTC is output immediately (1 trip detection logic). After the engine is warmed up, if the vehicle is driven in an urban area for 5 minutes, a DTC is output.

INSPECTION PROCEDURE

Tech Tips

Intelligent tester only:

By using the Active Test's Control the VVT-iE Linear (Bank 1) or Control the VVT-iE Linear (Bank 2) function, it can be determined if the VVT-iE system is malfunctioning.


  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG) and turn the tester ON.

  3. Clear the DTC Click here.

  4. Start the engine and warm it up.

  5. Enter the following menus: Powertrain / Engine / Active Test / Control the VVT-iE Linear (Bank 1) or Control the VVT-iE Linear (Bank 2) / All Data / VVT-iE Aim Angle #1 and VVT Change Angle #1 or VVT Change Angle #2 and VVT-iE Aim Angle #2.

  6. Perform the "Control the VVT-iE Linear (Bank 1) or Control the VVT-iE Linear (Bank 2)" operation with the engine speed at 1500 rpm.

    OK
    Active Test Movement Order Difference between "VVT-iE Aim Angle" and "VVT Change Angle"
    0 deg → 10 deg → 20 deg → 40 deg → 10 deg → 0 deg → 10 deg → END Within 4 DegFR

Tech Tips

Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0011 OR P0021)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG).

    3. Turn the tester ON.

    4. Enter the following menus: Powertrain / Engine / DTC.

    5. Read DTCs.

      Result
      Display (DTC Output) Proceed to
      P0011 or P0021 A
      P0011 or P0021 and other DTCs B

    B

    GO TO DTC CHART Click here

    A

  2. REPLACE CAMSHAFT TIMING GEAR ASSEMBLY (BANK 1 OR BANK 2)


    1. Replace the camshaft timing gear assembly Click here.


    NEXT

  3. CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the intelligent tester to the DLC3.

    2. Turn the engine switch on (IG) and turn the tester ON.

    3. Clear the DTC Click here.

    4. Start the engine and warm it up.

    5. Enter the following menus: Utility / Check Mode.

    6. Switch the ECM from normal mode to check mode.

    7. After idling the engine for 5 minutes, check for DTCs.

    8. Enter the following menus: DTC INFO / CURRENT CODE.

    9. Read DTC.

      Result
      Display (DTC Output) Proceed to
      No output A
      Other DTCs B

    B

    GO TO DTC CHART Click here

    A

    END