Click here

SLIDING ROOF HOUSING INSTALLATION

Click here
Click here Click here
  1. Click here

    INSTALL SLIDING ROOF HOUSING SUB-ASSEMBLY


    1. A01GXOI

      Temporarily install the sliding roof housing sub-assembly with the 12 bolts (vehicle body side) and 8 nuts.

    2. Tighten the 8 nuts.

      5.5 N*m 56 kgf*cm 49 in.*lbf

    3. Tighten the 12 bolts.

      8.0 N*m 82 kgf*cm 71 in.*lbf
    4. A01GZ43

      Tighten the 12 bolts.

      5.4 N*m 55 kgf*cm 48 in.*lbf
    5. A01H24XE01

      Connect the 4 drain hoses.

      Note:

      The clip must face toward the outside of the vehicle and also be above the lower surface of the sliding roof housing when installing the drain hoses.

    6. A01H1VA

      w/ Rear Seat Entertainment System:

      Attach the 2 clamps to connect the wire harness.

  2. Click here

    INSTALL REAR SLIDING ROOF HOUSING MOUNTING BRACKET LH


    1. Install the rear sliding roof housing mounting bracket LH with the 2 bolts.

      8.0 N*m 82 kgf*cm 71 in.*lbf

    2. Attach the clamp to connect the curtain shield airbag wire harness.

  3. Click here

    INSTALL REAR SLIDING ROOF HOUSING MOUNTING BRACKET RH

    Tip:

    Use the same procedure described for the LH side.

  4. Click here

    INSTALL SLIDING ROOF PANEL PLATE


    1. Attach the 2 guides to install the 2 sliding roof panel plates with the 4 bolts.

  5. Click here

    INSTALL FRONT SLIDING ROOF GARNISH


    1. Attach the 5 claws to install the front sliding roof garnish.

  6. Click here

    INSTALL SLIDING ROOF GLASS SUB-ASSEMBLY


    1. A01GWQEE01

      Using a T25 "TORX" driver, temporarily install the sliding roof glass sub-assembly with the 4 screws.

    2. A01GZVIE01

      Perform a level check.


      1. Check the difference in the level for "a" between the roof panel and the upper surface of the weatherstrip when the sliding roof glass sub-assembly is fully closed.

        Standard
        Area Measurement
        A - A -2.0 to +1.0 mm (-0.079 to +0.039 in.)
        B - B -1.0 to +2.0 mm (-0.039 to +0.079 in.)
        C - C -1.5 to +1.5 mm (-0.059 to +0.059 in.)
        D - D -1.0 to +1.5 mm (-0.039 to +0.059 in.)
        Tip:

        "+" represents the condition that the glass is above the panel level. "-" represents the condition that the glass is below the panel level.

      2. Perform a gap check.

        Check the gap between the roof panel and roof glass.

        Note:

        The gap must be even all around.

    3. A01GWQEE01

      Using a T25 "TORX" driver, tighten the 4 screws.

      5.5 N*m 56 kgf*cm 49 in.*lbf
  7. Click here

    CHECK FOR WATER LEAKS


    1. After adjusting the sliding roof glass sub-assembly, check for water leaks.

    2. If there are any leaks, readjust the sliding roof glass sub-assembly.

  8. Click here

    INSTALL SLIDING ROOF SIDE GARNISH LH


    1. Attach the 5 claws to install the sliding roof side garnish LH.

  9. Click here

    INSTALL SLIDING ROOF SIDE GARNISH RH

    Tip:

    Use the same procedure described for the LH side.

  10. Click here

    INSTALL NO. 1 ROOF SIDE AIR DUCT LH (w/ Rear Cooler)


    1. Install the No. 1 roof side air duct LH with the 3 clips.

  11. Click here

    INSTALL NO. 1 ROOF SIDE AIR DUCT RH (w/ Rear Cooler)

    Tip:

    Use the same procedure described for the LH side.

  12. Click here

    INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY LH

    (Click here)

  13. Click here

    INSTALL CURTAIN SHIELD AIRBAG ASSEMBLY RH

    Tip:

    Use the same procedure described for the LH side.

  14. Click here

    INSTALL ROOF HEADLINING ASSEMBLY (for Long Body)

    (Click here)

  15. Click here

    INSTALL ROOF HEADLINING ASSEMBLY (for Standard Body)

    (Click here)

  16. Click here

    CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  17. Click here

    INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02

      Attach the battery service hole cover LH with the clip and fastening tape.

      Table 1. Text in Illustration
      *A for Standard
      *B for Ottoman
  18. Click here

    INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  19. Click here

    INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

  20. Click here

    INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

  21. Click here

    CHECK SRS WARNING LIGHT

    (Click here)