ROOF HEADLINING (for Long Body) REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  2. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  3. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  4. REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape

      Detach the clip, fastening tape and remove the battery service hole cover LH.

  5. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Click here.

  6. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. REMOVE FRONT SEAT ASSEMBLY

    Click here

  8. REMOVE REAR SEAT ASSEMBLY (for Fixed Type)

    Click here

  9. REMOVE REAR SEAT ASSEMBLY (for Power Seat)

    Click here

  10. REMOVE REAR SEAT ASSEMBLY (for 4-Passenger with Ottoman)

    Click here

  11. REMOVE REAR SEAT ASSEMBLY (for 5-Passenger with Ottoman)

    Click here

  12. REMOVE FRONT DOOR SCUFF PLATE LH

    A01H28AE06

    1. Put protective tape around the front door scuff plate LH.

      Text in Illustration
      *1 Protective Tape

    2. Using moulding remover D, detach the 4 clips.

    3. A01H1FL

      Detach the 7 claws and remove the front door scuff plate LH.

  13. REMOVE FRONT DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE COWL SIDE TRIM BOARD LH

    A01GYTX

    1. Detach the 3 claws and remove the cowl side trim board LH.

  15. REMOVE COWL SIDE TRIM BOARD RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE FRONT PILLAR GARNISH LH

    A01GXWPE01
    Text in Illustration
    *1 Front Pillar Garnish Clip

    1. Pull the upper part of the front pillar garnish LH toward the inside of the cabin and detach the 2 clips.

      Tech Tips

      Make the front pillar garnish LH hang down from the front pillar garnish clip.

    2. A01H25TE01
      Text in Illustration
      *1 Front Pillar Garnish Clip
      *2 Protective Tape

      Turn the end of the front pillar garnish clip 90° with needle-nose pliers and remove it from the front pillar garnish LH.

      Note


      • Front pillar garnish clips are reusable if they are not removed from the vehicle and have no damage.

      • Replace the front pillar garnish clips with new ones if they are removed from the vehicle.

      Tech Tips

      Tape the tips of the needle-nose pliers before use.

    3. Pull the front pillar garnish LH to detach the guide and remove it.

    4. A01H29KE06
      Text in Illustration
      *1 Adhesive Tape
      *2 Protective Cover

      Protect the curtain shield airbag assembly LH.

      Completely cover the curtain shield airbag assembly LH with a cloth or nylon sheet and secure the ends of the cover with adhesive tape as shown in the illustration.

      Note

      Cover the curtain shield airbag assembly LH with a protective cover as soon as the front pillar garnish LH is removed.

  17. REMOVE FRONT PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  18. REMOVE REAR DOOR SCUFF PLATE LH

    A01GX1AE04

    1. Put protective tape around the rear door scuff plate LH.

      Text in Illustration
      *1 Protective Tape

    2. Using moulding remover D, detach the 4 clips.

    3. A01GWSM

      Detach the 7 claws and remove the rear door scuff plate LH.

  19. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  20. REMOVE CENTER LOWER PILLAR GARNISH LH

    A01GYU3

    1. Detach the 2 claws and 6 clips, and remove the center lower pillar garnish LH.

  21. REMOVE CENTER LOWER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  22. REMOVE CENTER UPPER PILLAR GARNISH LH

    A01GZUS

    1. Remove the 2 screws.

    2. Detach the claw, guide and remove the center upper pillar garnish LH.

    3. Pass the front seat outer belt floor anchor through the center upper pillar garnish LH.

  23. REMOVE CENTER UPPER PILLAR GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE SHOULDER BELT ANCHOR COVER LH

    A01GYLJ

    1. Slide the shoulder belt anchor cover in the direction of the arrow to detach the 6 claws and remove it from the center upper pillar garnish LH.

  25. REMOVE SHOULDER BELT ANCHOR COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. REMOVE REAR SEAT SIDE GARNISH LH

    A01GW72

    1. Detach the 6 claws and remove the rear seat side garnish LH.

  27. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. REMOVE INNER ROOF SIDE GARNISH LH

    A01GW31E10
    Text in Illustration
    *1 Clip A

    1. Pull the inner roof side garnish LH away from the body and detach the 4 clips (do not detach clip A).

    2. Detach the 2 claws of the guide, and pull the inner roof side garnish LH in the direction of the arrow to remove it.

      Tech Tips

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  29. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  30. REMOVE MAP LIGHT ASSEMBLY


    1. Using a screwdriver, detach the 2 claws and open the 2 covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.

    3. Using moulding remover D, detach the 2 clips and remove the map light assembly.

    4. Disconnect the 2 connectors.

      A01GZ6PE04
      Text in Illustration
      *1 Protective Tape - -

  31. REMOVE SPOT LIGHT LENS (w/ Rear Seat Entertainment System)

    A01H1S2

    1. Detach the 4 claws and remove the spot light lens.

  32. REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Rear Seat Entertainment System)

    A01GZS3

    1. Remove the 2 screws.

    2. Detach the 6 clips and 2 claws and remove the roof console box assembly.

    3. w/o Infrared Ray Sensor:

      Disconnect the connector.

    4. w/ Infrared Ray Sensor:

      Disconnect the 2 connectors.

  33. REMOVE SPOT LIGHT LENS (for 5-Passenger with Ottoman)

    A01GX3WE01
    Text in Illustration
    *1 Protective Tape

    1. Using a screwdriver, detach the 4 claws and remove the spot light lens.

      Tech Tips

      Tape the screwdriver tip before use.

  34. REMOVE ROOF CONSOLE BOX ASSEMBLY (for 5-Passenger with Ottoman)

    A01H0I5

    1. Remove the 2 screws.

    2. Detach the 2 claws, 2 clips and 2 hooks and remove the roof console box assembly.

    3. Disconnect the 2 connectors.

  35. REMOVE SPOT LIGHT ASSEMBLY (w/o Rear Seat Entertainment System)

    A01GYMU

    1. Using moulding remover D, detach the 4 claws and remove the spot light assembly.

    2. Disconnect the connector.

  36. REMOVE REAR VANITY LIGHT ASSEMBLY

    Tech Tips

    Use the same procedure to remove the vanity light assembly on the other side.


    1. Using a screwdriver, detach the 4 claws and remove the lens.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Remove the 2 screws.

    3. Using moulding remover D, detach the claw and remove the vanity light assembly.

    4. Disconnect the connector.

      A01H0BME02
      Text in Illustration
      *1 Protective Tape - -

  37. REMOVE ROOF SIDE REGISTER BEZEL LH

    A01GWCJ

    1. Remove the screw.

    2. Detach the claw and remove the roof side register bezel LH.

  38. REMOVE ROOF SIDE REGISTER BEZEL RH

    Tech Tips

    Use the same procedure described for the LH side.

  39. REMOVE ASSIST GRIP SUB-ASSEMBLY

    A01H22JE09
    Text in Illustration
    *1 Protective Tape

    Tech Tips

    Use the same procedure for all the assist grips.


    1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the 2 clips and remove the assist grip sub-assembly.

  40. REMOVE VISOR BRACKET COVER

    A01H2C7

    Tech Tips

    Use the same procedure to remove the visor bracket cover on the other side.


    1. Using moulding remover D, detach the 4 claws and remove the visor bracket cover.

  41. REMOVE VISOR ASSEMBLY LH

    A01GYQ3

    1. Remove the 2 screws and visor assembly LH.

  42. REMOVE VISOR ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  43. REMOVE VISOR HOLDER

    Tech Tips

    Use the same procedure to remove the visor holder on the other side.


    1. Turn the visor holder approximately 45° and pull it out as shown in the illustration.

    2. Detach the 2 claws and remove the visor holder.

      A01GY15E09
      Text in Illustration
      *a 45° - -

  44. REMOVE RAIN SENSOR COVER


    1. w/o Lane Keeping Assist System:

      Click here

    2. w/ Lane Keeping Assist System:

      Click here

  45. REMOVE INNER REAR VIEW MIRROR ASSEMBLY


    1. w/o Automatic High Beam System:

      Click here

    2. w/ Automatic High Beam System:

      Click here

  46. REMOVE OBJECT RECOGNITION CAMERA (w/ Lane Keeping Assist System)


    1. Partially remove the roof headlining assembly.

      Tech Tips

      It is not necessary to completely remove the roof headlining. Slightly lower the front section of the roof headlining so that the object recognition camera can be removed.

    2. Disconnect the 3 connectors.

    3. Detach the 2 wire harness clamps.

    4. Detach the claw and disconnect the connector clamp.

    5. Remove the 3 bolts.

    6. Detach the clip and remove the object recognition camera.

      A01GZXAE01
      Text in Illustration
      *A w/o Night View System *B w/ Night View System

  47. REMOVE WINDSHIELD GLASS

    Click here

  48. REMOVE ROOF HEADLINING ASSEMBLY

    A01GZZX

    1. Disconnect the roof wire connectors and detach each wire harness clamp from the front pillar LH.

    2. A01GYLFE01
      Text in Illustration
      *A w/ Lane Keeping Assist System

      Disconnect each connector and each wire harness clamp.

    3. A01H29I

      w/o Rear Seat Entertainment System:

      Detach the hook, 12 claws, 10 fasteners and 4 clips.

    4. A01GZRK

      w/ Rear Seat Entertainment System:

      Detach the hook, 12 claws, 8 fasteners and 4 clips.

    5. A01GXRL

      Remove the roof headlining assembly through the front of the vehicle.

      Note

      Be careful not to damage the roof headlining assembly when taking it out.

  49. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the front door opening trim weatherstrip LH.

  50. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.

  51. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH


    1. Remove the rear door opening trim weatherstrip.

  52. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP RH

    Tech Tips

    Use the same procedure described for the LH side.