REAR DOOR SUNSHADE ASSEMBLY REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  2. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  3. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  4. REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape

      Detach the clip, fastening tape and remove the battery service hole cover LH.

  5. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Click here.

  6. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A01GYVW

      Using a screwdriver, detach the 3 claws and remove the rear door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  8. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

    A01GZMDE01

    1. Apply protective tape to the area around the rear power window regulator switch assembly with rear door armrest base panel.

    2. Using a clip remover, detach the 2 clips in the order shown in the illustration.

      Text in Illustration
      *1 Protective Tape
    3. A01GXAJ

      Disconnect the connector.

    4. Remove the screw and illumination light.

    5. Remove the rear power window regulator switch assembly with rear door armrest base panel.

  9. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01H024

      for Long Body:


      1. Remove the 3 screws.

      2. Detach the 14 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A01GZ7Y

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the rear door trim board sub-assembly LH.

    2. A01GYMJ

      for Standard Body:


      1. Remove the 3 screws.

      2. Detach the 12 clips.

        Note

        Do not use a tool to detach the clips of the rear door trim board sub-assembly LH.

      3. A01GZ7Y

        Disconnect the 2 cables from the inside handle.

      4. Disconnect the connectors and remove the rear door trim board sub-assembly LH.

  10. REMOVE REAR DOOR TRIM COVER LH


    1. A01GYTL

      Remove the cushion.

    2. Using a clip remover, detach the 5 clips and remove the rear door trim cover LH.

  11. REMOVE REAR DOOR FRAME GARNISH LH


    1. A01GZ6G

      w/o Rear Door Sunshade:


      1. Remove the screw and detach the clip.

      2. Detach the claws and remove the rear door frame garnish LH.

    2. A01GWM7

      w/ Rear Door Sunshade:


      1. Detach the 2 clips.

      2. Detach the claws and remove the rear door frame garnish LH.

  12. REMOVE REAR DOOR NO. 2 FRAME GARNISH LH


    1. A01H12XE04
      Text in Illustration
      *A w/o Rear Door Sunshade
      *B w/ Rear Door Sunshade

      Detach the claws and remove the rear door No. 2 frame garnish LH.

  13. REMOVE REAR CURTAIN SUB-ASSEMBLY LH


    1. A01GYSR

      for Standard Body:


      1. Remove the 10 screws.

      2. Detach the 3 clips and remove the rear curtain sub-assembly LH.

      3. Disconnect the connector

    2. A01GX7R

      for Long Body:


      1. Remove the 10 screws.

      2. Detach the 4 clips and remove the rear curtain sub-assembly LH.

      3. Disconnect the connector