FRONT DOOR BELT MOULDING REMOVAL

Tech Tips


  • Use the same procedure for the RH side and LH side.

  • The procedure listed below is for the LH side.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  3. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  4. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  5. REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape

      Detach the clip, fastening tape and remove the battery service hole cover LH.

  6. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. REMOVE FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. A01GWOPE03
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 3 claws and remove the front door inside handle bezel plug LH.

      Tech Tips

      Tape the screwdriver tip before use.

  8. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL


    1. A01GWMP

      Using a moulding remover D, detach the 2 clips.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

      Tech Tips

      Tape the screwdriver tip before use.

  9. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01GYVZ

      Remove the 3 screws.

    2. Detach the 13 clips and remove the front door trim board sub-assembly LH.

    3. Disconnect the connector.

    4. A01GWSZ

      Disconnect the 2 cables from the inside handle.

  10. REMOVE FRONT MULTIPLEX NETWORK DOOR ECU LH


    1. A01GXMU

      Remove the 2 screws and front multiplex network door ECU LH.

    2. Disconnect the 3 connectors.

  11. REMOVE FRONT DOOR NO. 2 SERVICE HOLE COVER LH


    1. A01GX98

      Remove the front door No. 2 service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  12. REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH

    Click here

  13. REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP LH


    1. A01H1P3

      Remove the front door glass inner weatherstrip LH by pulling it upward in the direction indicated by the arrow in the illustration.

  14. REMOVE FRONT DOOR TRIM COVER LH


    1. A01GYADE01
      Text in Illustration
      *1 Cushion

      Remove the cushion.

    2. Using a clip remover, detach the 5 clips.

  15. REMOVE DOOR FRAME GARNISH LH


    1. A01GWW6

      Remove the 2 clips and door frame garnish LH.

  16. REMOVE FRONT DOOR BELT MOULDING REAR END COVER LH


    1. A01H1RL

      Detach the claw and front door belt moulding end cover rear LH.

  17. REMOVE FRONT DOOR WEATHERSTRIP LH

    A01H0QQE10

    1. Remove the clip and front door weatherstrip.

      Tech Tips

      Lift up the front door No. 3 weatherstrip to remove the front door No. 2 weatherstrip, as the No. 2 weatherstrip is affixed to the inner side of the No. 3 weatherstrip.

  18. REMOVE FRONT DOOR WINDOW FRONT FRAME MOULDING LH


    1. Put a 4 mm (0.157 in.) drill bit into a drill.

    2. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill, as shown in the illustration.

      Tech Tips

      Tape the 4 mm (0.157 in.) drill bit to prevent the drill bit from going too deep.

    3. Lightly press the drill against each of the 6 front door window frame moulding rivets labeled (A) and (B) shown in the illustration, and drill off each rivet's flange.

      Tech Tips


      • The rivets labeled (A) are the installation rivets of the front door window frame moulding.

      • The rivets labeled (B) are the installation rivets for both the front door window frame moulding and front door belt moulding.

      • Do not remove the front door window belt moulding's rivet labeled (C).

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Do not pry the rivets with the drill, because this may cause damage to the installation holes of the rivets or the drill bit.

      • Be careful of the drilled rivets as they may become hot.

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.

    5. Detach the clip and remove the window frame moulding.

      A01GZI6E01

  19. REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01GY51

      Remove the front door service hole cover LH.

      Tech Tips

      Remove the remaining tape on the door.

  20. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the front door ECU LH.

    2. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    3. Connect the cable to the negative (-) battery terminal.

    4. Remove the hole plug.

    5. A01GYAX

      Move the front window regulator sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.

    6. Disconnect the cable from the negative (-) battery terminal.

      Note

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

    7. Remove the 2 bolts.

      Note

      Be careful when removing the bolts as the glass may fall and become damaged.

    8. A01GW9L

      Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

      Tech Tips

      Remove the glass upward.

      Note

      Be careful not to damage the glass.

    9. Remove the power window regulator master switch assembly with front door armrest base panel.

    10. Disconnect the front door ECU LH.

  21. REMOVE FRONT DOOR GLASS RUN LH


    1. Remove the front door glass run LH.

  22. REMOVE FRONT DOOR FRONT LOWER FRAME UPPER COVER LH

    A01H11U

    1. Detach the 2 clips and remove the front door front lower frame upper cover LH.

  23. REMOVE FRONT DOOR BELT MOULDING SUB-ASSEMBLY LH


    1. Put a 4.5 mm (0.177 in.) drill bit into a drill.

    2. Wind tape around the drill bit approximately 5 mm (0.197 in.) from the tip of the drill as shown in the illustration.

    3. Lightly press the drill against the rivet shown in the illustration, and drill off the rivet's flange.

      A01GYZXE02

      CAUTION:

      Be careful of the drilled rivet as it may become hot.

      Note


      • Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.

      • Do not pry the rivet with the drill, because this may cause damage to the installation holes of the rivet or the drill bit.

    4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled area.

    5. A01GWL0

      Remove the 2 screws.

    6. A01GXNS

      for Type A:


      1. Loosen the 5 belt line screws indicated by the arrows in the illustration.

      2. Remove the 4 screws and front door sub-assembly LH.

    7. A01GWA1

      for Type B:


      1. Loosen the 3 belt line screws indicated by the arrows in the illustration.

      2. Remove the 4 screws and front door sub-assembly LH.