REAR DOOR WINDOW FRAME MOULDING (for Standard Body) INSTALLATION

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.


  1. INSTALL REAR DOOR WINDOW UPPER FRAME MOULDING LH


    1. Attach the clip to install the window frame moulding.

    2. Install a nose piece to an air riveter or hand riveter. Then insert the mandrel part of a new φ4 mm waterproof rivet into the nose piece.

    3. Using the air riveter or hand riveter, install the 6 rivets shown in the illustration.

      Tech Tips


      • As there are 2 types of rivets, be sure to install the rivets to the correct locations.

        Rivet Rivet Type
        (A) Short Type or Long Type
        (B) Long Type

      • If the rivet cannot be cut, pull it once and cut it.

      A01GXU8E01

      Note


      • A01GWS7E02

        Do not pry the rivet with the riveter, as this will cause damage to the riveter and mandrel.

      • A01GZMQE02

        Confirm that the rivets are seated properly against the moulding.

      • Do not tilt the riveter when installing the rivet to the moulding.

      • Do not leave any space between the rivet head and moulding.

      • A01H0UKE02

        Do not leave any space between the moulding and door frame. Firmly hold together the 2 items while installing the rivet.

  2. INSTALL REAR DOOR NO. 2 WEATHERSTRIP LH


    1. Attach the clip to install the rear door No. 2 weatherstrip LH.

  3. INSTALL REAR DOOR NO. 3 WEATHERSTRIP LH


    1. A01GZAKE02
      Text in Illustration
      *1 Double-sided Tape

      Place double-sided tape on the rear door No. 3 weatherstrip LH as shown in the illustration.

    2. A01GY16

      Attach the 2 claws to install the rear door No. 3 weatherstrip LH.

  4. INSTALL REAR DOOR FRAME GARNISH LH


    1. w/o Rear Door Sunshade:


      1. Attach the claws.

      2. Attach the clip to install the rear door frame garnish LH with screw.

    2. w/ Rear Door Sunshade:


      1. Attach the claws.

      2. Attach the 2 clips to install the rear door frame garnish LH.

  5. INSTALL REAR DOOR TRIM COVER LH


    1. Attach the 5 clips to install the rear door trim cover LH.

    2. Install the cushion.

  6. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (w/o Rear Door Sunshade)


    1. for Long Body:


      1. A01GXAA

        Connect the 2 cables to the inside handle.

      2. Connect the connector.

      3. Install the rear door trim board sub-assembly LH with the 3 screws and 13 clips.

    2. for Standard Body:


      1. A01GXAA

        Connect the 2 cables to the inside handle.

      2. Connect the connector.

      3. Install the rear door trim with the 3 screws and 11 clips.

  7. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. for Long Body:


      1. A01GXAA

        Connect the 2 cables to the inside handle.

      2. Connect the connector.

      3. Install the rear door trim board sub-assembly LH with the 3 screws and 14 clips.

    2. for Standard Body:


      1. A01GXAA

        Connect the 2 cables to the inside handle.

      2. Connect the connector.

      3. Install the rear door trim board sub-assembly LH with the 3 screws and 12 clips.

  8. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE PANEL

    A01GXK8

    1. Install the illumination light with the screw.

    2. Connect the connector.

    3. Attach the 2 clips to install the rear power window regulator switch assembly with rear door armrest base panel.

  9. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. Attach the 3 claws to install the rear door inside handle bezel plug LH.