Tech Tips
The installation should be performed in the order of LH to RH.
After installing the torsion bar, use your hand to open and close the luggage door. Make sure the luggage door can open and close smoothly.
INSTALL NO. 2 LUGGAGE COMPARTMENT DOOR TORSION BAR SUPPORT
Squeeze the two sides of the No. 2 luggage compartment door torsion bar support indicated by the arrows and install it as shown in the illustration.
INSTALL LUGGAGE DOOR HINGE TORSION BAR LH
| *a | Installation Hole (for Adjustment) |
| *b | Installation Hole |
Set the tip of the luggage door hinge torsion bar LH in the installation hole in the center. The upper and lower holes are used for adjustment.
Connect the luggage door hinge torsion bar LH to the body RH side.
Connect the luggage door hinge torsion bar LH to the luggage compartment door torsion bar support.
Using SST, install the luggage door hinge torsion bar LH to the luggage door hinge and body LH side
INSTALL LUGGAGE DOOR HINGE TORSION BAR RH
| *a | Installation Hole (for Adjustment) |
| *b | Installation Hole |
Set the tip of the luggage door hinge torsion bar RH in the installation hole in the center. The upper and lower holes are used for adjustment.
Connect the luggage door hinge torsion bar RH to the body LH side.
Connect the luggage door hinge torsion bar RH to the luggage compartment door torsion bar support.
Using SST, install the luggage door hinge torsion bar RH to the luggage door hinge and body RH side.
Attach the 3 clips and install the luggage door wire.
INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH
Install the luggage compartment trim cover assembly RH with the claw and 2 clips.
INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH
Install the luggage compartment trim cover assembly LH with the claw and 2 clips.
INSTALL REAR FLOOR FINISH PLATE
Attach the 4 clips to install the rear floor finish plate.
Install the 3 clips.
INSTALL TOOL BOX (w/o Spare Tire)
Install the tool box with the 2 clips.
INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)
INSTALL FRONT LUGGAGE COMPARTMENT TRIM COVER
| *A | w/o Rear Cooler |
| *B | w/ Rear Cooler |
Attach the 4 claws to install the front luggage compartment trim cover.
Install the 3 clips.
INSTALL NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Connect the connector.
Attach the 2 claws to Install the No. 1 luggage compartment light assembly.
INSTALL NO. 1 COOLER COVER (w/ Rear Cooler)
Attach the 5 clips to install the No. 1 cooler cover.
INSTALL DECK TRIM SIDE BOARD RH
| *A | w/ Spare Tire |
| *B | w/o Spare Tire |
w/ Spare Tire:
Install the deck trim side board RH with the clip.
w/o Spare Tire:
Attach the clip to install the deck trim side board RH.
INSTALL ROPE HOOK ASSEMBLY
Install the 4 rope hook assemblies with the 4 bolts.
INSTALL ROPE HOOK
Install the 4 rope hooks.
INSTALL BATTERY SERVICE HOLE COVER LH
| *A | for Standard |
| *B | for Ottoman |
Attach the battery service hole cover LH with the clip and fastening tape.
INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)
Attach the 2 clips to install the deck trim side board LH.
INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)
INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)
INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER LH
Install the luggage compartment door hinge cover LH with the 3 clips.
INSTALL LUGGAGE COMPARTMENT DOOR HINGE COVER RH
Install the luggage compartment door hinge cover RH with the 3 clips.