HOOD ADJUSTMENT

REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

1. Disconnect the connector.

2. Remove the 3 bolts.

3. Detach the 2 guides and remove the millimeter wave radar sensor assembly.

INSTALL MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

1. Connect the connector.

2. Attach the 2 guides and install the millimeter wave radar sensor assembly with the 3 bolts in alphabetical order.

   5.5 N*m

   56 kgf*cm

   49 in.*lbf

ADJUST MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Dynamic Radar Cruise Control System)

1. Before adjusting the radar beam axis, prepare the vehicle as follows.

   
   

   1. Check the tire pressure and adjust it if necessary.

   2. Remove all excess weight from the vehicle (luggage, heavy objects, etc.).

2. w/ Air Suspension:

   Adjust the vehicle's height to the standard height.

3. Check and adjust the vertical direction of the radar sensor.

   
   
   1. 

      Remove dust, oil and foreign matter from the radar sensor's level rack.

   2. Set a level on the radar sensor's level rack.

   3. 

      Check that the level's air bubble is within the red frame.

      OK
      Level's air bubble is within red frame.

      If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the level's air bubble is within the red frame.

      Tip:
      

      • The adjustable range within the red frame of the level is +/-0.2°.

      • The target angle is +0.2° (upward angle of 0.2°).

      Result
      Adjustment Direction Adjustment Procedure Adjustment Angle Vertical adjustment Upward direction: Turn bolt A in minus (- )direction For 1 complete turn of screwdriver, sensor moves about 0.12° Downward direction: Turn bolt A in plus (+) direction

4. 

   Adjust the reflector height.

   
   

   1. Adjust the reflector so that the center of SST reflector is the same height as the millimeter wave radar sensor.

      09870-60000	09870-60010
      09870-60040

      Tip:

      Prepare a 10 m (32.8 ft.) string, a string with a sharp-pointed weight (plumb bob), and a 5 m (16.4 ft.) tape measure.

5. Place the reflector.

   
   
   1. 

      From the center of the front bumper (center of the emblem), hang a weight with a pointed tip, and mark point B on the ground.

   2. 

      From the center of the rear bumper (center of the emblem), hang a weight with a pointed tip, and mark point A on the ground.

   3. Using a piece of string that uses point A as a starting point and that passes through point B, make a straight line on the ground ahead of the vehicle 5 m (16.4 ft.) or more from point B.

      Tip:
      

      • Make sure to secure the string (using tape, etc.) when it is taut.

      • Lightly flick the string with your fingers several times to confirm that the string is aligned above point B.

   4. 

      Using a tape measure, measure 10 mm (0.394 in.) to the left of the 5000 mm (16.4 ft.) position. Place the reflector at that position.

      Note:

      Perform the operation as precisely as possible.

6. Check the radar beam axis.

   
   

   1. Connect the intelligent tester to the DLC3.

   2. Turn the power switch on (IG).

   3. Turn the intelligent tester main switch ON, and turn the cruise control main switch ON.

   4. Select "Auto" from the intelligent tester display screen. *1

   5. Select "Radar Cruise" from the display screen.

   6. Select the appropriate menu item.

      
      

      1. For vehicles with lane recognition camera: select "w/ LKA System" from the display screen.

      2. For vehicles without lane recognition camera: select "w/o LKA System" from the display screen.

   7. Select "Radar Cruise" from the display screen.

   8. Select "Utility" from the display screen.

   9. Select "Beam Axis Adjustment" from the display screen.

   10. Follow the intelligent tester display and select "Next".

       Note:
       

       • Turn the cruise control main switch ON before pressing Next.

       • Make sure there is at least 20 cm (7.9 inches) between the radar sensor and any nearby individuals.

         CAUTION:

         Do not come within 20 cm (7.9 inches) of the radar sensor.

   11. Check the following items on the laser cruise divergence data screen.

       CAUTION:

       While using the intelligent tester's beam axis adjustment mode, the actual direction and angle of the radar sensor may be different from the intelligent tester's data. In such a case, the deviation is displayed on the combination meter's multi-information display.

       
       

       1. Confirm that the distance value is approximately 5 m (16.4 ft.).

          Tip:
          

          • A value between 0.0 and 6.3 m (20.7 ft.) is indicated.

          • If the distance is 0 m (0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the NOTICE at the beginning of this adjustment procedure).

       2. Confirm that the left/right side value is between 0.0 and 6.3°.

          Tip:

          If the distance is 0 m (0 ft.), the sensor cannot detect the target. Reconfirm that there is no metal in the specified area in front of the vehicle (refer to the NOTICE at the beginning of this adjustment procedure).

7. Check and adjust the horizontal direction of the radar sensor.

   
   

   1. Check that the divergence of the radar beam axis is 0°.

      Standard
      0° (Both right and left)

      If the axis is not as specified, use a screwdriver to adjust bolt B until the divergence of the radar beam axis is 0°.

   2. 

      Based on the measured divergence of the beam axis, turn and adjust bolt B for horizontal adjustment of the millimeter wave radar sensor using a screwdriver.

      Result
      Adjustment Direction Adjustment Procedure Adjustment Angle Horizontal adjustment Right direction: Turn bolt B in plus (+) direction For 1 complete turn of screwdriver, sensor moves about 0.07° Left direction: Turn bolt B in minus (- )direction

      Tip:

      If the value does not change to 0°, it is possible that the sensor is aiming at something different. Reconfirm that there are no reflective materials in the surrounding area.

   3. Select "Next". The driving learning value is automatically reset.

      Tip:

      A buzzer will sound for 10 seconds or more.

   4. Disconnect the intelligent tester from the DLC3.

8. Recheck and readjust the vertical direction of the radar sensor.

   
   
   1. 

      Set a level on the radar sensor's level rack.

   2. 

      Check that the level's air bubble is within the red frame.

      OK
      Level's air bubble is within the red frame.

      If the bubble is not within the red frame, use a screwdriver to adjust bolt A until the level's air bubble is within the red frame.

      Tip:
      

      • The adjustable range within the red frame is +/-0.2°.

      • The target angle is +0.2° (upward angle of 0.2°).

      Result
      Adjustment Direction Adjustment Procedure Adjustment Angle Vertical adjustment Upward direction: Turn bolt A in minus (- )direction For 1 complete turn of screwdriver, sensor moves about 0.12° Downward direction: Turn bolt A in plus (+) direction