REAR SEATBACK HEATER (for Fixed Seat Type) REMOVAL

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY


    1. A01GXB4E01
      Text in Illustration
      *A w/ Seat Heater System

      Detach the 3 front hooks of the bench type rear seat cushion assembly from the vehicle body.

      Note

      Follow the instructions below carefully as the cushion frame deforms easily.

    2. Choose a hook to detach first. Place your hands near the hook. Then lift the bench type rear seat cushion assembly to detach the hook.

    3. Repeat the step above for the other hook.

    4. Detach the 2 rear hooks of the bench type rear seat cushion assembly from the bench type rear seatback assembly.

    5. w/ Seat Heater System:

      Disconnect the 2 connectors.

    6. Remove the bench type rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  2. REMOVE BENCH TYPE REAR SEATBACK ASSEMBLY


    1. A01H1P1

      Remove the 2 bolts and nut to disconnect the 3 belt anchors of the rear seat 3 point type belt assembly LH, rear seat 3 point type belt assembly RH and rear center seat outer belt assembly.

    2. A01H0KUE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws to open the 2 caps of the rear seat shoulder belt guide.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure to open the 2 caps on the other side.

    3. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

      Tech Tips

      Use the same procedure to disconnect the rear seat outer belt on the other side.

    4. Lower the rear center armrest assembly.

    5. A01GWGA

      Lower the rear center seat headrest assembly.

    6. A01GZT1E04

      Detach the 2 clips. Then detach the hook by lowering the rear seat armrest hole board, and remove it.

    7. A01GZ6J

      w/ Seat Heater System:


      1. Remove the bolt and pull out the junction block.

      2. Disconnect the connector.

    8. A01GWRJE02

      Remove the 4 bolts and nut.

    9. Lift the bench type rear seatback assembly to detach the 2 hooks.

    10. Disconnect the rear center armrest assembly connector to remove the bench type rear seatback assembly.

      Note

      Be careful not to damage the vehicle body.

  3. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY


    1. A01GXYVE01

      Detach the wire harness clamp.

    2. Remove the 2 nuts and rear seat center armrest assembly.

  4. REMOVE REAR SEAT HEADREST ASSEMBLY


    1. Remove the rear seat headrest assembly.

      Tech Tips

      Use the same procedure to remove the rear seat headrest assembly on the other side.

  5. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY

    A01H1TF

    1. Remove the 2 bolts and rear center seat headrest assembly.

  6. REMOVE REAR SEAT ARMREST HOLE COVER

    A01H1T6

    1. Detach the 2 clips to remove the rear seat armrest hole cover.

  7. REMOVE REAR SEAT HEADREST SUPPORT

    A01GY7A

    1. Detach the 4 claws to remove the 2 rear seat headrest supports.

      Tech Tips

      Use the same procedure to remove the rear seat headrest support on the other side.

  8. REMOVE REAR SEAT SHOULDER BELT GUIDE LH

    A01GZLL

    1. Remove the 3 screws and rear seat shoulder belt guide LH.

  9. REMOVE REAR SEAT SHOULDER BELT GUIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  10. REMOVE REAR SEAT CLIMATE CONTROL ECU LH


    1. A01H222

      Disconnect the 2 connectors.

    2. Remove the 2 nuts and rear seat climate control ECU LH.

  11. REMOVE REAR SEAT CLIMATE CONTROL ECU RH

    Tech Tips

    Use the same procedures described for the LH side.

  12. REMOVE REAR SEAT WIRE RH


    1. Disconnect the 2 connectors.

    2. Remove the 14 wire harness clamps labeled A.

    3. Detach the 2 wire harness clamps labeled B to remove the rear seat wire RH.

      A01GYV3E01

  13. REMOVE BENCH TYPE REAR SEATBACK COVER


    1. for LH Side:


      1. Remove the 30 hog rings and bench type rear seatback cover from the bench type rear seat seatback pad.

        A01H1HVE01
        Text in Illustration
        *a Front View *b Rear View

    2. for RH Side:


      1. Remove the 31 hog rings and bench type rear seatback cover from the bench type rear seat seatback pad.

        A01GYC9E01
        Text in Illustration
        *a Front View *b Rear View