Click here

FRONT SEATBACK HEATER INSTALLATION

Click here
Click here Click here
CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart (Click here).

Click here
  1. Click here

    INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. Set the separate type front seat back cover in place.

    2. for Sport Package:

      Attach the 4 pieces of fastening tape.

    3. A01H1WXE01

      Using hog ring pliers, install the separate type front seat back cover to the front seatback pad with 20 new hog rings as shown in the illustration.

      Note:

      • Be careful not to damage the separate type front seat back cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat back cover.

      Tip:

      Install the hog rings at the cutouts.

      Table 1. Text in Illustration
      *A except Sport Package *B for Sport Package
      *1 Fastening Tape *2 Hog Ring Pliers
  2. Click here

    INSTALL FRONT SEATBACK FRAME ASSEMBLY LH


    1. A01H1MM

      Temporarily install the front seatback frame assembly LH with the 4 bolts.

    2. Push the front seatback frame assembly LH towards the rear, and tighten the 4 bolts.

      43 N*m 439 kgf*cm 32 ft.*lbf

    3. for Driver Side:


      1. A01GXPN

        w/ Active Headrest:

        Attach the 9 clamps and connect the 4 connectors.

      2. A01GZX8

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 4 connectors.

    4. for Front Passenger Side:


      1. A01GWJC

        w/ Active Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      2. A01GXUO

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      3. A01GYZL

        w/ Retractable Headrest:

        Attach the 7 clamps and connect the 2 connectors.

  3. Click here

    INSTALL FRONT SEATBACK COVER WITH PAD


    1. Set the front seatback cover with pad in place.

    2. A01H120

      Attach the 9 hooks to install the front seatback cover with pad.

    3. Attach the 3 clips.

    4. A01GYQ4

      Attach the front seatback cover bracket with the bolt.

      5.5 N*m 56 kgf*cm 49 in.*lbf
  4. Click here

    INSTALL POWER SEAT SWITCH ASSEMBLY (w/ Shoulder Switch)


    1. Connect the connector.

    2. A01GWDI

      Attach the 2 claws to install the power seat switch assembly.

  5. Click here

    INSTALL FRONT SEAT HEADREST SUPPORT


    1. Attach the 4 claws to install the 2 front seat headrest supports.

  6. Click here

    INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. w/ Active Headrest, w/ Pre-crash Intelligent Headrest:


      1. A01GXHC

        Install the front seat headrest assembly with the 2 pins.

        Note:

        w/ Active Headrest:

        When replacing a deployed active headrest inflator, always replace it together with the front seat headrest assembly.

    2. w/ Retractable Headrest:

      Install the front seat headrest assembly.

  7. Click here

    INSTALL FRONT SEAT CUSHION ASSEMBLY LH


    1. A01GWZDE01

      Install the front seat cushion assembly with the 4 bolts.

      21 N*m 214 kgf*cm 15 ft.*lbf

    2. Attach the hook.

      Table 2. Text in Illustration
      *1 Hook
    3. A01H21A

      Attach the hook.

    4. A01GYFU

      Install the 2 clips.

    5. A01GXIA

      Connect the connector and attach the 2 wire harness clamps.

    6. A01GYQ6

      Connect the connector and attach the wire harness clamp.

    7. A01GYQ8

      Connect the connector and attach the wire harness clamp.

    8. Attach the 4 claws to connect duct of the seat climate control blower LH.

    9. A01H1M8

      Connect the connector.

    10. A01GYWF

      Connect the duct of the seat climate control blower LH with the 3 screws.

    11. A01GYTY

      Attach the 2 claws to install the No. 6 air duct.

  8. Click here

    INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01H1Y4E01

      Connect the connector and attach the wire harness clamp.

    2. Attach the 2 hooks to install the front seatback board sub-assembly LH.

      Table 3. Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

    3. Install the 2 screws.

  9. Click here

    INSTALL FRONT SEAT INNER CUSHION SHIELD LH


    1. Attach the claw to install the front seat inner cushion shield LH.

    2. Install the 3 screws.

  10. Click here

    INSTALL FRONT SEAT INNER BELT ASSEMBLY LH


    1. Install the front seat inner belt assembly LH with the nut.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

      Table 4. Text in Illustration
      *1 Protruding Part

    2. Attach the claw to connect the connector.

    3. Attach the 6 wire harness clamps.

    4. A01GXDJE01

      Connect the 2 connectors.

      Table 5. Text in Illustration
      *A for Driver Side *B for Front Passenger Side
  11. Click here

    INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)


    1. A01H1UL

      Install the front seat inner No. 1 cushion shield LH with the 3 screws.

  12. Click here

    INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH (for Front Passenger Side)


    1. A01H0CQE01

      Install the front seat inner No. 1 cushion shield RH with the 3 screws.

      Table 6. Text in Illustration
      *A for Ottoman
      *B except Ottoman
  13. Click here

    INSTALL FRONT SEAT CUSHION SHIELD LH


    1. Connect the 2 connectors.

    2. Attach the 2 claws to install the front seat cushion shield LH as indicated by the arrows in the order shown in the illustration.

    3. Install the 3 screws.

    4. A01H14B

      Attach the rubber band of the front seatback board sub-assembly LH to the front seat adjuster assembly LH.

  14. Click here

    INSTALL FRONT SEAT ASSEMBLY LH

    (Click here)

  15. Click here

    CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  16. Click here

    INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02

      Attach the battery service hole cover LH with the clip and fastening tape.

      Table 7. Text in Illustration
      *A for Standard
      *B for Ottoman
  17. Click here

    INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  18. Click here

    INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

  19. Click here

    INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

  20. Click here

    CHECK SRS WARNING LIGHT

    (Click here)

  21. Click here

    CHECK FRONT SEAT ASSEMBLY


    1. Check the power seat operation:

      (Click here)

    2. Check the climate control seat system:

      (Click here)