AIR HOSE (for Ottoman) REMOVAL

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  3. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  4. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  5. REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape

      Detach the clip, fastening tape and remove the battery service hole cover LH.

  6. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH

    Click here

  8. REMOVE REAR SEAT ASSEMBLY

    Click here

  9. REMOVE REAR DOOR SCUFF PLATE LH

    A01GX1AE04

    1. Put protective tape around the rear door scuff plate LH.

      Text in Illustration
      *1 Protective Tape

    2. Using moulding remover D, detach the 4 clips.

    3. A01GWSM

      Detach the 7 claws and remove the rear door scuff plate LH.

  10. REMOVE REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. REMOVE REAR SEAT SIDE GARNISH LH

    A01GW72

    1. Detach the 6 claws and remove the rear seat side garnish LH.

  12. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. REMOVE INNER ROOF SIDE GARNISH LH

    A01GW31E10
    Text in Illustration
    *1 Clip A

    1. Pull the inner roof side garnish LH away from the body and detach the 4 clips (do not detach clip A).

    2. Detach the 2 claws of the guide, and pull the inner roof side garnish LH in the direction of the arrow to remove it.

      Tech Tips

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  14. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. A01GWDN

      except 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 3 belt guides.

    2. for 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 2 belt guides.

    3. A01GY1H

      except 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel assembly. Then pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    4. A01H1AU

      for 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel assembly. Then pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.

    5. Disconnect the solar sensor connector and remove the package tray trim panel.

  16. REMOVE ROOF SIDE NO. 2 AIR DUCT LH


    1. A01H1EA

      Remove the clip.

    2. Detach the 2 claws and remove the No. 2 roof side air duct LH.

  17. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. A01GXJK

      Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. w/ Tension Reducer System:

      Disconnect the tension reducer connector.

    3. A01H0NV

      Remove the bolt.

    4. Detach the claw and remove the rear seat 3 point type belt assembly LH.

  18. REMOVE AIR HOSE

    A01GYCX

    1. Using a screwdriver, detach the 2 claws and remove the hose clamp.

    2. Disconnect the air hose connector.

    3. A01GXLV

      for LHD:


      1. Remove the 2 hose clamps and bolt.

      2. Detach the 2 claws and remove the air hose.

    4. A01GYOA

      for RHD:


      1. Remove the hose clamp and bolt.

      2. Detach the 2 claws and remove the air hose.