LUMBAR SUPPORT ADJUSTER ASSEMBLY (for Front Side) INSTALLATION

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)


    1. Attach the 2 claws to install the lumbar support adjuster assembly LH.

    2. Rotate the snap in the direction indicated by the arrow in the illustration to attach the snap to the lumbar support adjuster assembly LH.

      Tech Tips

      Use the same procedure to attach the snap on the other side.

      A01GYJ2
    3. A01H28E

      Install the 4 bolts.

  2. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY RH (w/o Lumbar Support)


    1. Attach the 2 claws to install the lumbar support adjuster assembly RH.

    2. Rotate the snap in the direction indicated by the arrow in the illustration to attach the snap to the lumbar support adjuster assembly RH.

      Tech Tips

      Use the same procedure to attach the snap on the other side.

      A01GWXR
    3. A01H1UC

      Install the 2 bolts.

  3. INSTALL FRONT SEATBACK FRAME ASSEMBLY LH


    1. A01H1MM

      Temporarily install the front seatback frame assembly LH with the 4 bolts.

    2. Push the front seatback frame assembly LH towards the rear, and tighten the 4 bolts.

      Torque:
      43 N*m  { 439 kgf*cm, 32 ft.*lbf }

    3. for Driver Side:


      1. A01GXPN

        w/ Active Headrest:

        Attach the 9 clamps and connect the 4 connectors.

      2. A01GZX8

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 4 connectors.

    4. for Front Passenger Side:


      1. A01GWJC

        w/ Active Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      2. A01GXUO

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      3. A01GYZL

        w/ Retractable Headrest:

        Attach the 7 clamps and connect the 2 connectors.

  4. INSTALL FRONT SEATBACK COVER WITH PAD


    1. Set the front seatback cover with pad in place.

    2. A01H120

      Attach the 9 hooks to install the front seatback cover with pad.

    3. Attach the 3 clips.

    4. A01GYQ4

      Attach the front seatback cover bracket with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  5. INSTALL POWER SEAT SWITCH ASSEMBLY (w/ Shoulder Switch)


    1. Connect the connector.

    2. A01GWDI

      Attach the 2 claws to install the power seat switch assembly.

  6. INSTALL FRONT SEAT HEADREST SUPPORT

    A01GZ16

    1. Attach the 4 claws to install the 2 front seat headrest supports.

  7. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. w/ Active Headrest, w/ Pre-crash Intelligent Headrest:


      1. A01GXHC

        Install the front seat headrest assembly with the 2 pins.

        Note

        w/ Active Headrest:

        When replacing a deployed active headrest inflator, always replace it together with the front seat headrest assembly.

    2. w/ Retractable Headrest:

      Install the front seat headrest assembly.

  8. INSTALL FRONT SEAT CUSHION ASSEMBLY LH


    1. A01GWZDE01

      Install the front seat cushion assembly with the 4 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Attach the hook.

      Text in Illustration
      *1 Hook
    3. A01H21A

      Attach the hook.

    4. A01GYFU

      Install the 2 clips.

    5. A01GXIA

      Connect the connector and attach the 2 wire harness clamps.

    6. A01GYQ6

      Connect the connector and attach the wire harness clamp.

    7. A01GYQ8

      Connect the connector and attach the wire harness clamp.

    8. Attach the 4 claws to connect duct of the seat climate control blower LH.

    9. A01H1M8

      Connect the connector.

    10. A01GYWF

      Connect the duct of the seat climate control blower LH with the 3 screws.

    11. A01GYTY

      Attach the 2 claws to install the No. 6 air duct.

  9. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01H1Y4E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Connect the connector and attach the wire harness clamp.

    2. Attach the 2 hooks to install the front seatback board sub-assembly LH.

    3. Install the 2 screws.

  10. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    A01GW8J

    1. Attach the claw to install the front seat inner cushion shield LH.

    2. Install the 3 screws.

  11. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    A01GX6QE02
    Text in Illustration
    *1 Protruding Part

    1. Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. Attach the claw to connect the connector.

    3. Attach the 6 wire harness clamps.

    4. Connect the 2 connectors.

      A01GXDJE01
      Text in Illustration
      *A for Driver Side *B for Front Passenger Side

  12. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)


    1. A01H1UL

      Install the front seat inner No. 1 cushion shield LH with the 3 screws.

  13. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH (for Front Passenger Side)


    1. A01H0CQE01
      Text in Illustration
      *A for Ottoman
      *B except Ottoman

      Install the front seat inner No. 1 cushion shield RH with the 3 screws.

  14. INSTALL FRONT SEAT CUSHION SHIELD LH

    A01H1N9E01

    1. Connect the 2 connectors.

    2. Attach the 2 claws to install the front seat cushion shield LH as indicated by the arrows in the order shown in the illustration.

    3. Install the 3 screws.

    4. A01H14B

      Attach the rubber band of the front seatback board sub-assembly LH to the front seat adjuster assembly LH.

  15. INSTALL FRONT SEAT ASSEMBLY LH

    Click here

  16. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  17. INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman

      Attach the battery service hole cover LH with the clip and fastening tape.

  18. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  19. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  20. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  21. CHECK SRS WARNING LIGHT

    Click here

  22. CHECK FRONT SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. w/ Climate Control Seat System:

      Click here