Click here

REAR POWER SEAT MOTOR ASSEMBLY (for Ottoman) REMOVAL

Click here
Click here Click here
CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • for Power Seat:

    Before removing the rear seat, make sure to move the seat 37 mm (1.46 in.) from the rearmost position.

  • for Ottoman:

    Before removing the rear seat, make sure to move the seat 17 mm (0.67 in.) from the rearmost position.

Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work (Click here).

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

  3. Click here

    REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

  4. Click here

    REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  5. Click here

    REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02

      Detach the clip, fastening tape and remove the battery service hole cover LH.

      Table 1. Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape
  6. Click here

    DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  7. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY LH


    1. Detach the 2 front hooks of the rear seat cushion assembly LH from the rear No. 2 seat adjuster assembly.

      Note:

      • If the areas close to the insertion location of the rear seat cushion lock hooks (A) are not lifted straight up, the cushion spring may become deformed.

      • When lifting the rear seat cushion assembly, lift it quickly so that force is applied directly to the hooks. Do not lift it slowly.

      Specification
      Area Measurement
      a 114 mm (4.49 in.)
      b 100 mm (3.94 in.)

    2. Detach the rear hook of the rear seat cushion assembly LH to remove the rear seat cushion assembly LH from the rear seatback spring assembly LH.

      Note:

      Be careful not to damage the vehicle body.

    3. Disconnect the connector.

  8. Click here

    REMOVE REAR SEAT CUSHION ASSEMBLY RH


    1. Connect the cable to the negative (-) auxiliary battery terminal.

    2. Operate the ottoman switch to move the ottoman to the return position.

    3. Disconnect the cable from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    4. A01GYEKE01

      Put protective tape as shown in the illustration.

    5. Remove the 2 seat cushion cover hooks.

    6. Remove the 2 nuts and disconnect the seat cushion ottoman part.

    7. Lift the corners of the rear seat cushion assembly RH to disconnect the 2 rear seat cushion lock hooks.

      Note:

      • If the areas close to the insertion location of the rear seat cushion lock hooks (cushion assembly corners) are not lifted straight up, the cushion spring may become deformed.

      • When lifting the rear seat cushion assembly, lift it quickly so that force is applied directly to the hooks. Do not lift it slowly.

    8. Detach the rear hook of the rear seat cushion assembly RH to remove the rear seat cushion assembly RH from the rear seatback spring assembly RH.

      Note:

      Be careful not to damage the vehicle body.

    9. Disconnect the connector.

      Table 2. Text in Illustration
      *1 Protective Tape
      *2 Seat Cover Hook
      *3 Nut
      *4 Rear Seat Cushion Lock Hook
      *5 Rear Hook
  9. Click here

    REMOVE REAR CENTER SEAT CUSHION ASSEMBLY (w/ Center Seat)


    1. A01GYL5

      Detach the front hook of the rear center seat cushion assembly from the vehicle body.

      Note:

      The cushion frame deforms easily. To avoid deforming the rear center seat cushion assembly, place your hands near the hook, and then pull up on the rear center seat cushion assembly.

    2. Detach the rear hook of the rear center seat cushion assembly to remove the rear center seat cushion assembly from the center seatback frame sub-assembly.

      Note:

      Be careful not to damage the vehicle body.

  10. Click here

    REMOVE REAR SEAT CONSOLE BOX (w/ Rear Console Box)

    (Click here)

  11. Click here

    REMOVE REAR SEATBACK ASSEMBLY LH


    1. A01GZD3

      Remove the bolt and disconnect the anchor part of the rear seat 3 point type belt assembly LH.

    2. A01H0KUE03

      Using a screwdriver, detach the 2 claws and open the 2 caps of the rear seat shoulder belt guide.

      Tip:

      Tape the screwdriver tip before use.

      Table 3. Text in Illustration
      *1 Protective Tape

    3. Disconnect the rear seat 3 point type belt assembly from the shoulder belt guide.

    4. A01GYN6

      Remove the bolt and pull out the junction block.

    5. Disconnect the 2 connectors.

    6. A01GZN8

      Detach the 7 wire harness clamps and disconnect the 3 connectors.

    7. A01GZ4EE01

      Detach the 3 pieces of fastening tape and using a clip remover, detach the clip.

      Table 4. Text in Illustration
      *1 Fastening Tape

    8. Remove the 2 nuts and disconnect the air duct from the vehicle.

    9. Disconnect the rear seatback assembly LH from the rear No. 2 seat adjuster assembly and lift the rear seatback assembly LH upwards to remove it.

      Note:

      Be careful not to damage the vehicle body.

  12. Click here

    REMOVE REAR SEATBACK ASSEMBLY RH


    1. A01GZL5

      Remove the bolt and disconnect the anchor part of the rear seat 3 point type belt assembly RH.

    2. A01GYO9E01

      Using a screwdriver, detach the 2 claws and open the 2 caps of the rear seat shoulder belt guide.

      Tip:

      Tape the screwdriver tip before use.

      Table 5. Text in Illustration
      *1 Protective Tape

    3. Remove the seat belt from the shoulder belt guide.

    4. A01GYAI

      Remove the bolt and pull out the junction block.

    5. Disconnect the 3 connectors.

    6. A01GZBZ

      Detach the 6 wire harness clamps and disconnect the 3 connectors.

    7. A01H06FE01

      Remove the nut, detach the 2 claws and disconnect the air hose.

    8. Detach the 3 pieces of fastening tape and using a clip remover, detach the clip.

    9. Remove the 2 nuts and disconnect the air duct from the vehicle.

    10. Disconnect the rear seatback assembly RH from the rear No. 2 seat adjuster assembly and lift the rear seatback assembly RH upwards to remove it.

      Note:

      Be careful not to damage the vehicle body.

      Table 6. Text in Illustration
      *1 Air Hose
      *2 Fastening Tape
      *3 Air Duct
  13. Click here

    REMOVE REAR SEAT CENTER ARMREST ASSEMBLY (w/ Center Seat)


    1. Lower the rear seat center armrest assembly.

    2. A01GWGA

      Raise the rear center seat headrest assembly.

    3. A01H1UME04

      Detach the 2 clips.

    4. Detach the hook by lowering the rear seat armrest hole board, and remove it.

    5. A01GYO5

      Remove the 2 bolts, nut and rear seat center armrest assembly.

      Note:

      Be careful not to damage the vehicle body.

    6. Disconnect the 2 connectors.

  14. Click here

    REMOVE REAR NO. 2 SEAT ADJUSTER ASSEMBLY


    1. A01GW56

      w/ Center Seat:

      Remove the nut and disconnect the anchor part of the rear center seat outer belt assembly.

    2. A01GWCG

      Remove the 4 bolts, nut and rear No. 2 seat adjuster assembly.

      Note:

      Be careful not to damage the vehicle body.

    3. Disconnect the air duct from the vehicle body.

  15. Click here

    REMOVE REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY LH


    1. A01GW6I

      Remove the nut and rear seat belt inner anchor bracket assembly LH.

  16. Click here

    REMOVE SEAT CLIMATE CONTROL CONTROLLER LH


    1. A01GYB6

      Remove the rear No. 2 seat cushion pad.

    2. A01H0FQ

      Detach the 2 wire harness clamps and disconnect the 2 connectors.

    3. A01GXX7

      Remove the 2 screws.

    4. Detach the 2 claws to remove the seat climate control controller LH.

  17. Click here

    REMOVE REAR SEAT CLIMATE CONTROL BLOWER LH


    1. A01H06E

      Disconnect the connector.

    2. A01GWIC

      Remove the 3 nuts and rear seat climate control blower LH.

  18. Click here

    REMOVE REAR SEAT AIRBAG ASSEMBLY RH


    1. A01GXP2

      Detach the wire harness clamp and disconnect the connector.

    2. Remove the 3 bolts and rear seat airbag assembly RH.

  19. Click here

    REMOVE REAR NO. 1 SEAT ADJUSTER ASSEMBLY


    1. Remove the 4 bolts, nut and rear No. 1 seat adjuster assembly.

      Note:

      Be careful not to damage the vehicle body.

    2. Disconnect the air duct from the vehicle body.

  20. Click here

    REMOVE REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY RH


    1. A01H04F

      Remove the nut and rear seat belt inner anchor bracket assembly RH.

  21. Click here

    REMOVE SEAT CLIMATE CONTROL CONTROLLER RH

    Tip:

    Use the same procedures described for the LH side.

  22. Click here

    REMOVE REAR SEAT CLIMATE CONTROL BLOWER RH

    Tip:

    Use the same procedures described for the LH side.

  23. Click here

    REMOVE REAR SEAT RECLINING ADJUSTER ASSEMBLY RH


    1. Disconnect the connector.

    2. Remove the 4 nuts and rear seat reclining adjuster assembly RH.

      Note:

      Be careful not to damage the vehicle body.

  24. Click here

    REMOVE REAR SEAT HEADREST ASSEMBLY


    1. A01GWUN

      Remove the 2 pins and rear seat headrest assembly.

      Tip:

      Use the same procedure to remove the rear seat headrest assembly on the other side.

  25. Click here

    REMOVE REAR SEAT HEADREST SUPPORT


    1. A01GY11

      Detach the 4 claws to remove the 2 rear seat headrest supports.

      Tip:

      Use the same procedure to remove the rear seat headrest support on the other side.

  26. Click here

    REMOVE REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY


    1. A01GX1O

      Detach the wire harness clamp and disconnect the 2 connectors.

    2. Remove the 2 bolts.

    3. Detach the 2 claws to remove the rear No. 1 seat headrest adjuster sub-assembly.

  27. Click here

    REMOVE REAR SEAT SHOULDER BELT GUIDE LH


    1. A01GZLL

      Remove the 3 screws and rear seat shoulder belt guide LH.

  28. Click here

    REMOVE POSITION CONTROL ECU ASSEMBLY


    1. Disconnect the 2 connectors.

    2. Remove the 2 nuts and position control ECU assembly.

      Tip:

      Use the same procedure to remove the position control ECU assembly on the other side.

  29. Click here

    REMOVE REAR SEAT CLIMATE CONTROL ECU LH


    1. Disconnect the 2 connectors.

    2. Remove the 2 nuts and rear seat climate control ECU LH.

  30. Click here

    REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY


    1. Disconnect the connector.

    2. Detach the guide and remove the seat heater control sub-assembly.

      Tip:

      Use the same procedure to remove the seat heater control sub-assembly on the other side.

  31. Click here

    REMOVE REAR SEAT COVER CAP LH


    1. A01H22F

      Detach the 5 claws to remove the rear seat cover cap LH.

  32. Click here

    REMOVE REAR SEAT LOCK BASE LH


    1. A01H0K4

      Remove the 3 screws and rear seat lock base LH.

  33. Click here

    REMOVE REAR SEATBACK COVER WITH PAD LH


    1. Remove the nut and detach the seatback cover bracket.

    2. Disconnect the connector.

    3. A01H0KCE01

      Detach the 8 hooks and remove the 19 hog rings and rear seatback cover with pad LH from the rear seatback spring assembly LH.

      Table 7. Text in Illustration
      *1 Seatback Cover Bracket *2 Hook
  34. Click here

    REMOVE REAR SEATBACK CLIMATE CONTROL BLOWER LH


    1. Remove the felt pad.

      Table 8. Text in Illustration
      *1 Felt Pad

    2. Disconnect the 3 connectors and detach the wire harness clamps.

    3. Remove the 3 nuts.

    4. Remove the 2 screws and rear seatback climate control blower LH.

  35. Click here

    REMOVE REAR SEAT WIRE LH


    1. Disconnect the 3 connectors.

    2. Detach the 11 wire harness clamps to remove the rear seat wire LH.

  36. Click here

    REMOVE REAR SEAT SHOULDER BELT GUIDE RH

    Tip:

    Use the same procedures described for the LH side.

  37. Click here

    REMOVE REAR SEAT CLIMATE CONTROL ECU RH

    Tip:

    Use the same procedures described for the LH side.

  38. Click here

    REMOVE REAR SEAT COVER CAP RH

    Tip:

    Use the same procedures described for the LH side.

  39. Click here

    REMOVE REAR SEAT LOCK BASE RH

    Tip:

    Use the same procedures described for the LH side.

  40. Click here

    REMOVE REAR SEATBACK CLIMATE CONTROL BLOWER RH

    Tip:

    Use the same procedures described for the LH side.

  41. Click here

    REMOVE REAR SEATBACK COVER WITH PAD RH


    1. Remove the nut and detach the seatback cover bracket.

    2. Disconnect the connector.

    3. A01GY4FE02

      Detach the 7 hooks and remove the 20 hog rings and rear seatback cover with pad RH from the rear seatback spring assembly RH.

      Table 9. Text in Illustration
      *1 Seatback Cover Bracket *2 Hook
  42. Click here

    REMOVE REAR SEAT WIRE RH


    1. Disconnect the 3 connectors.

    2. Detach the 11 wire harness clamps to remove the rear seat wire RH.

  43. Click here

    REMOVE SUB SEATBACK PLATE SUB-ASSEMBLY


    1. A01H101

      Detach the 2 claws to disconnect the 2 air hoses.

    2. Detach the 2 clamps to remove the upper part of the sub seatback plate sub-assembly.

    3. A01GXB7

      Detach the 2 hose clamps to disconnect the air hose.

    4. Detach the 4 clamps to remove the lower part of the sub seatback plate sub-assembly.