Click here

REAR POWER SEAT MOTOR ASSEMBLY (for Power Seat) INSTALLATION

Click here
Click here Click here
CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart (Click here).

Click here
  1. Click here

    INSTALL REAR SEAT WIRE LH


    1. A01GXEE

      Attach the 11 wire harness clamps to install the rear seat wire LH.

    2. Connect the 3 connectors.

  2. Click here

    INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER LH


    1. Install the rear seatback climate blower LH with the 2 screws.

    2. Install the 3 nuts.

    3. Connect the 3 connectors and attach the wire harness clamp.

    4. Install a new felt pad.

      Table 1. Text in Illustration
      *1 Felt Pad
  3. Click here

    INSTALL REAR SEATBACK COVER WITH PAD LH


    1. Set the rear seatback cover with pad LH in place.

    2. Using hog ring pliers, install the rear seatback cover with pad LH to the rear seatback spring assembly LH with 19 new hog rings.

      Note:

      • Be careful not to damage the rear seatback cover with pad LH.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seatback cover with pad LH.

    3. Attach the 8 hooks.

    4. Connect the connector.

    5. A01GZXWE01

      Attach the seatback cover bracket with the nut.

      5.6 N*m 57 kgf*cm 50 in.*lbf
      Table 2. Text in Illustration
      *1 Seatback Cover Bracket *2 Hook
      *3 Hog Ring Pliers - -
  4. Click here

    INSTALL REAR SEAT LOCK BASE LH


    1. A01H0K4

      Install the rear seat lock base LH with the 3 screws.

  5. Click here

    INSTALL REAR SEAT COVER CAP LH


    1. A01H22F

      Attach the 5 claws to install the rear seat cover cap LH.

  6. Click here

    INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY


    1. Attach the guide to install the seat heater control sub-assembly.

    2. Connect the connector.

      Tip:

      Use the same procedure to install the seat heater control sub-assembly on the other side.

  7. Click here

    INSTALL REAR SEAT CLIMATE CONTROL ECU LH


    1. Install the rear seat climate control ECU LH with the 2 nuts.

    2. Connect the 2 connectors.

  8. Click here

    INSTALL POSITION CONTROL ECU ASSEMBLY


    1. Install the position control ECU assembly with the 2 nuts.

    2. Connect the 2 connectors.

      Tip:

      Use the same procedure to install the position control ECU assembly on the other side.

  9. Click here

    INSTALL REAR SEAT SHOULDER BELT GUIDE LH


    1. Install the rear seat shoulder belt guide LH with the 3 screws.

  10. Click here

    INSTALL REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY


    1. A01GX1O

      Attach the 2 claws to install the rear No. 1 seat headrest adjuster sub-assembly LH with the 2 bolts.

    2. Connect the 2 connectors and attach the wire harness clamp.

      Tip:

      Use the same procedure to install the rear No. 1 seat headrest adjuster sub-assembly on the other side.

  11. Click here

    INSTALL REAR SEAT HEADREST SUPPORT


    1. Attach the 4 claws to install the 2 rear seat headrest supports.

      Tip:

      Use the same procedure to install the rear seat headrest support on the other side.

  12. Click here

    INSTALL REAR SEAT HEADREST ASSEMBLY


    1. Install the rear seat headrest assembly with the 2 pins.

      Tip:

      Use the same procedure to install the rear seat headrest assembly on the other side.

  13. Click here

    INSTALL REAR SEAT WIRE RH

    Tip:

    Use the same procedures described for the LH side.

  14. Click here

    INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER RH

    Tip:

    Use the same procedures described for the LH side.

  15. Click here

    INSTALL REAR SEATBACK COVER WITH PAD RH

    Tip:

    Use the same procedures described for the LH side.

  16. Click here

    INSTALL REAR SEAT LOCK BASE RH

    Tip:

    Use the same procedures described for the LH side.

  17. Click here

    INSTALL REAR SEAT COVER CAP RH

    Tip:

    Use the same procedures described for the LH side.

  18. Click here

    INSTALL REAR SEAT CLIMATE CONTROL ECU RH

    Tip:

    Use the same procedures described for the LH side.

  19. Click here

    INSTALL REAR SEAT SHOULDER BELT GUIDE RH

    Tip:

    Use the same procedures described for the LH side.

  20. Click here

    INSTALL REAR SEAT CLIMATE CONTROL BLOWER LH


    1. A01GWIC

      Install the rear seat climate control blower LH with the 3 nuts.

    2. A01H06E

      Connect the connector.

  21. Click here

    INSTALL SEAT CLIMATE CONTROL CONTROLLER LH


    1. A01GXX7

      Attach the claws to connect the seat climate control controller LH.

    2. Install the 2 screws.

    3. A01H0FQ

      Connect the 2 connectors and attach the 2 wire harness clamps.

    4. A01GYB6

      Install a new rear No. 2 seat cushion pad.

  22. Click here

    INSTALL REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY LH


    1. Install the rear seat belt inner anchor bracket assembly LH with the nut.

      21 N*m 214 kgf*cm 15 ft.*lbf
  23. Click here

    INSTALL REAR NO. 2 SEAT ADJUSTER ASSEMBLY


    1. A01GWCGE01

      Connect the air duct to the vehicle body.

    2. Install the rear No. 2 seat adjuster assembly with the 4 bolts and nut.

      for bolt A
      42 N*m 428 kgf*cm 31 ft.*lbf
      except bolt A
      20 N*m 204 kgf*cm 15 ft.*lbf
      Note:

      Be careful not to damage the vehicle body.

    3. A01GZRVE03

      Connect the anchor part of the rear center seat outer belt with the nut.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear center seat outer belt to overlap the protruding part of the anchor bracket.

      Table 3. Text in Illustration
      *1 Protruding Part
  24. Click here

    INSTALL REAR SEAT CLIMATE CONTROL BLOWER RH

    Tip:

    Use the same procedures described for the LH side.

  25. Click here

    INSTALL SEAT CLIMATE CONTROL CONTROLLER RH

    Tip:

    Use the same procedures described for the LH side.

  26. Click here

    INSTALL REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY RH

    Tip:

    Use the same procedures described for the LH side.

  27. Click here

    INSTALL REAR NO. 1 SEAT ADJUSTER ASSEMBLY


    1. A01H0QGE02

      Connect the air duct to the vehicle body.

    2. Install the rear No. 1 seat adjuster assembly with the 4 bolts and nut.

      for bolt A
      42 N*m 428 kgf*cm 31 ft.*lbf
      except bolt A
      20 N*m 204 kgf*cm 15 ft.*lbf
      Note:

      Be careful not to damage the vehicle body.

  28. Click here

    INSTALL REAR SEATBACK ASSEMBLY RH

    Tip:

    Use the same procedures described for the LH side.

  29. Click here

    INSTALL REAR SEATBACK ASSEMBLY LH


    1. Connect the rear seatback assembly LH to the rear No. 2 seatback adjuster assembly, and press down on the rear seatback assembly LH to install it to the rear No. 2 seatback adjuster assembly. Then connect the air duct to the vehicle body.

      Note:

      Be careful not to damage the vehicle body.

    2. Install the 2 nuts.

      20 N*m 204 kgf*cm 15 ft.*lbf

    3. Install the clip and attach the 3 pieces of fastening tape.

      Table 4. Text in Illustration
      *1 Fastening Tape
    4. A01GZN8

      Connect the 3 connectors and attach the 7 wire harness clamps.

    5. A01GYN6

      Connect the 2 connectors.

    6. Install the junction block with the bolt.

      30 N*m 306 kgf*cm 22 ft.*lbf
    7. A01GY4K

      Connect the seat belt to the shoulder belt guide.

    8. Attach the 2 claws to close the 2 caps.

    9. A01GWAIE03

      Connect the anchor part of the rear seat 3 point type belt assembly with the bolt.

      42 N*m 428 kgf*cm 31 ft.*lbf
      Note:

      Do not allow the anchor part of the rear seat 3 point type belt assembly to overlap protruding parts of the floor panel.

      Table 5. Text in Illustration
      *1 Protruding Part
  30. Click here

    INSTALL REAR SEAT CUSHION ASSEMBLY RH

    Tip:

    Use the same procedures described for the LH side.

  31. Click here

    INSTALL REAR SEAT CUSHION ASSEMBLY LH


    1. A01GWEX

      Connect the connector.

    2. Attach the rear hook of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

      Note:

      Be careful not to damage the vehicle body.

    3. Attach the 2 front hooks of the rear seat cushion assembly LH to the rear No. 2 seat adjuster assembly.

  32. Click here

    CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  33. Click here

    INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02

      Attach the battery service hole cover LH with the clip and fastening tape.

      Table 6. Text in Illustration
      *A for Standard
      *B for Ottoman
  34. Click here

    INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  35. Click here

    INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

  36. Click here

    INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

  37. Click here

    CHECK SRS WARNING LIGHT

    (Click here)

  38. Click here

    CHECK REAR SEAT ASSEMBLY


    1. Check the power seat operation:

      (Click here)

    2. Check the climate control seat system:

      (Click here)

    3. Check the seat vibration system:

      (Click here)