SEAT HEATER SWITCH (for Fixed Seat Type) INSTALLATION

Tech Tips

A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL REAR POWER SEAT SWITCH


    1. A01GWNC

      Install the rear power seat switch with the 4 screws.

  2. INSTALL REAR NO. 1 SEAT CENTER ARMREST PANEL


    1. A01H0QD

      Install the rear No. 1 seat center armrest panel to rear seat armrest hole board with the 3 screws.

    2. Connect the 2 connectors.

    3. A01H0M7E01

      Attach the 3 guides and 8 claws to install the rear No. 1 seat center armrest panel together with the rear seat armrest hole board by the arrows in the order shown in the illustration.

  3. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    1. Install the rear seat center armrest assembly with the 2 nuts.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

    2. Attach the wire harness clamp.

  4. INSTALL BENCH TYPE REAR SEATBACK ASSEMBLY

    Note

    Be careful not to damage the vehicle body.


    1. Set the bench type rear seatback assembly in place.

    2. A01GWKNE02

      Connect the rear center armrest assembly connector.

    3. Attach the 2 hooks on the backside of the bench type rear seatback assembly.

    4. Install the 4 bolts and nut.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
    5. A01GZ6J

      w/ Seat Heater System:


      1. Connect the connector.

      2. Install the junction block with the bolt.

        Torque:
        30 N*m  { 306 kgf*cm, 22 ft.*lbf }
    6. A01GZW5E02

      Attach the hook to the rear seat armrest hole board. Then attach the 2 clips to install the rear seat armrest hole board.

    7. A01H1N5

      While pressing the button, raise the rear center seat headrest assembly.

    8. Raise the rear center armrest assembly.

    9. A01GY4K

      Connect the rear seat outer belt to the rear seat shoulder belt guide.

      Tech Tips

      Use the same procedure to connect the rear seat outer belt on the other side.

    10. Attach the 2 claws to close the 2 caps of the rear seat shoulder belt guide.

      Tech Tips

      Use the same procedure to close the 2 caps on the other side.

    11. A01H1P1

      Connect the 2 seat belt anchors of the rear seat 3 point type belt assembly LH and rear seat 3 point type belt assembly RH with the 2 bolts and connect the seat belt anchor of the rear center seat outer belt assembly with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  5. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY

    Note

    Be careful not to damage the vehicle body.


    1. Set the bench type rear seat cushion assembly in place.

    2. A01GXB4E01
      Text in Illustration
      *A w/ Seat Heater System

      w/ Seat Heater System:

      Connect the 2 connectors.

    3. Attach the 2 rear hooks of the bench type rear seat cushion assembly to the bench type rear seatback assembly.

    4. Attach the 3 front hooks to install the bench type rear seat cushion assembly.

    5. Confirm that the bench type rear seat cushion assembly is firmly installed.

      Note

      When installing the bench type rear seat cushion assembly, make sure the seat belt buckle is not under the bench type rear seat cushion assembly.

  6. CHECK SEAT HEATER SYSTEM

    Click here

  7. CHECK REAR SUNSHADE SYSTEM

    Click here