AIR HOSE (for Ottoman) INSTALLATION

Tech Tips


  • Use the same procedure for LHD and RHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL AIR HOSE


    1. A01GXLV

      for LHD:


      1. Attach the 2 claws to install the air hose.

      2. Install the 2 hose clamps and bolt.

        Torque:
        9.8 N*m  { 100 kgf*cm, 87 in.*lbf }
    2. A01GYOA

      for RHD:


      1. Attach the 2 claws to install the air hose.

      2. Install the hose clamp and bolt.

        Torque:
        9.8 N*m  { 100 kgf*cm, 87 in.*lbf }

    3. Attach the 2 claws to install the hose clamp.

    4. A01GYCX

      Attach the 2 claws to connect the air hose connector.

  2. INSTALL REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH

    A01H096E01

    1. Insert the claw of the retractor (a) into the hole.

    2. Align the seat belt positioning hole with the claw and install the retractor of the rear seat 3 point type belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }
    3. A01GY6B

      Connect the pretensioner connector and lock the locking button as shown in the illustration.

    4. w/ Tension Reducer System:

      Connect the tension reducer connector.

  3. INSTALL ROOF SIDE NO. 2 AIR DUCT LH

    A01H1EA

    1. Attach the 2 claws to install the No. 2 roof side air duct LH.

    2. Install the clip.

  4. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. Connect the solar sensor connector.

    2. except 4-Passenger with Ottoman:

      Pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    3. for 4-Passenger with Ottoman:

      Pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.

    4. Insert the rear part of the package tray trim panel assembly into the rear sunshade assembly.

    5. Attach the 2 clips to install the package tray trim panel assembly.

    6. except 4-Passenger with Ottoman:

      Attach the 4 claws to install the 3 belt guides.

    7. for 4-Passenger with Ottoman:

      Attach the 4 claws to install the 2 belt guides.

  5. INSTALL INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  6. INSTALL INNER ROOF SIDE GARNISH LH

    A01H0IUE06
    Text in Illustration
    *1 Clip A

    1. Install a new clip A to the inner roof side garnish LH.

    2. Attach the 2 claws and 5 clips to install the inner roof side garnish LH.

  7. INSTALL REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. INSTALL REAR SEAT SIDE GARNISH LH


    1. Attach the 6 claws to install the rear seat side garnish LH.

  9. INSTALL REAR DOOR SCUFF PLATE RH

    Tech Tips

    Use the same procedure described for the LH side.

  10. INSTALL REAR DOOR SCUFF PLATE LH

    A01H1WQ

    1. Attach the 4 clips.

    2. Attach the 7 claws to install the rear door scuff plate LH.

  11. INSTALL REAR SEAT ASSEMBLY

    Click here

  12. INSTALL LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH

    Click here

  13. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  14. INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman

      Attach the battery service hole cover LH with the clip and fastening tape.

  15. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  16. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  17. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  18. CHECK SRS WARNING LIGHT

    Click here

  19. CHECK REAR SEAT ASSEMBLY


    1. Check the power seat operation:

      Click here

    2. Check the climate control seat system:

      Click here

    3. Check the seat vibration system:

      Click here