REAR SEAT ASSEMBLY (for Power Seat) REASSEMBLY

INSTALL REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY

1. Install the rear seat center armrest cup holder sub-assembly with the 2 screws.

INSTALL REAR POWER SEAT SWITCH

1. Install the rear power seat switch with the 4 screws.

INSTALL REAR NO. 1 SEAT CENTER ARMREST PANEL

1. Install the rear No. 1 seat center armrest panel to the rear seat armrest hole board with the 3 screws.

2. Connect the 2 connectors.

3. Attach the 3 guides and 8 claws to install the rear No. 1 seat center armrest panel together with the rear seat armrest hole board.

INSTALL TELEVISION SWITCH AND VOLUME ASSEMBLY

1. Install the television switch and volume assembly.

INSTALL CENTER SEATBACK FRAME SUB-ASSEMBLY

1. Install the center seatback frame sub-assembly to the rear center armrest assembly with the 2 nuts.

   Torque:

   20 N*m  { 204 kgf*cm, 15 ft.*lbf }

2. Attach the wire harness clamp.

INSTALL REAR SEAT ARMREST HOLE COVER

1. Attach the 2 clips to install the rear seat armrest hole cover.

INSTALL REAR CENTER SEAT HEADREST ASSEMBLY

1. Install the rear center seat headrest assembly with the 2 bolts.

   Torque:

   20 N*m  { 204 kgf*cm, 15 ft.*lbf }

INSTALL REAR CENTER SEAT CUSHION PAD

1. Install the rear center seat cushion pad to the rear center seat cushion frame.

INSTALL CENTER SEAT CUSHION COVER SUB-ASSEMBLY

INSTALL REAR SEAT CLIMATE CONTROL BLOWER LH

INSTALL AIR FILTER

1. Attach the 2 claws to install the air filter.

   Tech Tips

   Use the same procedure to install the air filter on the other side.

INSTALL SEAT CLIMATE CONTROL CONTROLLER LH

INSTALL REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY LH

1. Install the rear seat belt inner anchor bracket assembly LH with the nut.

   Torque:

   21 N*m  { 214 kgf*cm, 15 ft.*lbf }

INSTALL REAR SEAT WIRE LH

1. Attach the 11 wire harness clamps to install the rear seat wire LH.

2. Connect the 3 connectors.

INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER LH

Text in Illustration

*1

Felt Pad

1. Install the rear seatback climate blower LH with the 2 screws.

2. Install the 3 nuts.

3. Connect the 3 connectors and attach the wire harness clamp.

4. Install a new felt pad.

INSTALL SEPARATE TYPE REAR SEATBACK COVER LH

1. 

   Text in Illustration

   *1	Hog Ring Pliers

   Set the separate type rear seatback cover LH in place.

2. Using hog ring pliers, install the separate type rear seatback cover LH to the rear seatback pad LH with 10 new hog rings.

   Note

   
   

   • Be careful not to damage the separate type rear seatback cover LH.

   • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover LH.

INSTALL REAR SEATBACK COVER WITH PAD LH

INSTALL REAR SEAT LOCK BASE LH

INSTALL REAR SEAT COVER CAP LH

INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY

1. Attach the guide to install the seat heater control sub-assembly.

2. Connect the connector.

   Tech Tips

   Use the same procedure to install the seat heater control sub-assembly on the other side.

INSTALL REAR SEAT CLIMATE CONTROL ECU LH

1. Install the rear seat climate control ECU LH with the 2 nuts.

2. Connect the 2 connectors.

INSTALL POSITION CONTROL ECU ASSEMBLY

1. Install the position control ECU assembly with the 2 nuts.

2. Connect the 2 connectors.

   Tech Tips

   Use the same procedure to install the position control ECU assembly on the other side.

INSTALL REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY

1. Attach the 2 claws to install the rear No. 1 seat headrest adjuster sub-assembly with the 2 bolts.

2. Connect the 2 connectors and attach the wire harness clamp.

   Tech Tips

   Use the same procedure to install the rear No. 1 seat headrest adjuster sub-assembly on the other side.

INSTALL REAR SEAT HEADREST SUPPORT

1. Attach the 4 claws to install the 2 rear seat headrest supports.

   Tech Tips

   Use the same procedure to install the rear seat headrest support on the other side.

INSTALL REAR SEAT HEADREST ASSEMBLY

1. Install the rear seat headrest assembly with the 2 pins.

   Tech Tips

   Use the same procedure to install the rear seat headrest assembly on the other side.

INSTALL REAR SEAT SHOULDER BELT GUIDE LH

1. Install the rear seat shoulder belt guide LH with the 3 screws.

INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER LH

1. 

   Text in Illustration

   *1	Hog Ring Pliers

   Set the separate type rear seat cushion cover LH in place.

2. Using hog ring pliers, install the separate type rear seat cushion cover LH to the rear seat cushion pad LH with 15 new hog rings.

   Note

   
   

   • Be careful not to damage the separate type rear seat cushion cover LH.

   • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover LH.

INSTALL REAR SEAT CUSHION SPRING ASSEMBLY LH

Text in Illustration

*1	Hog Ring Pliers

1. Set the rear seat cushion spring assembly LH in place.

2. Using hog ring pliers, install the rear seat cushion spring assembly LH to the rear seat cushion cover with pad LH with 22 new hog rings.

   Note

   
   

   • Be careful not to damage the rear seat cushion cover with pad LH.

   • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the rear seat cushion cover with pad LH.

INSTALL REAR SEAT CLIMATE CONTROL BLOWER RH

INSTALL SEAT CLIMATE CONTROL CONTROLLER RH

INSTALL REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY RH

INSTALL REAR SEAT WIRE RH

INSTALL REAR SEATBACK CLIMATE CONTROL BLOWER RH

INSTALL SEPARATE TYPE REAR SEATBACK COVER RH

INSTALL REAR SEATBACK COVER WITH PAD RH

INSTALL REAR SEAT LOCK BASE RH

INSTALL REAR SEAT COVER CAP RH

INSTALL REAR SEAT CLIMATE CONTROL ECU RH

INSTALL REAR SEAT SHOULDER BELT GUIDE RH

INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH

INSTALL REAR SEAT CUSHION SPRING ASSEMBLY RH