REAR SEAT ASSEMBLY (for Power Seat) DISASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE REAR SEAT CUSHION SPRING ASSEMBLY LH


    1. A01H1Y2

      Remove the 22 hog rings and rear seat cushion spring assembly LH from the rear seat cushion cover with pad LH.

  2. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER LH


    1. A01GZ4H

      Remove the 15 hog rings and separate type rear seat cushion cover LH from the rear seat cushion pad LH.

  3. REMOVE REAR SEAT SHOULDER BELT GUIDE LH


    1. A01GZLL

      Remove the 3 screws and rear seat shoulder belt guide LH.

  4. REMOVE REAR SEAT HEADREST ASSEMBLY


    1. A01GWUN

      Remove the 2 pins and rear seat headrest assembly.

      Tech Tips

      Use the same procedure to remove the rear seat headrest assembly on the other side.

  5. REMOVE REAR SEAT HEADREST SUPPORT


    1. A01GY11

      Detach the 4 claws and remove the 2 rear seat headrest supports.

      Tech Tips

      Use the same procedure to remove the rear seat headrest support on the other side.

  6. REMOVE REAR NO. 1 SEAT HEADREST ADJUSTER SUB-ASSEMBLY


    1. A01GX1O

      Detach the wire harness clamp and disconnect the 2 connectors.

    2. Remove the 2 bolts.

    3. Detach the 2 claws to remove the rear No. 1 seat headrest adjuster sub-assembly.

      Tech Tips

      Use the same procedure to remove the rear No. 1 seat headrest adjuster sub-assembly on the other side.

  7. REMOVE POSITION CONTROL ECU ASSEMBLY


    1. A01GXM9

      Disconnect the 2 connectors.

    2. Remove the 2 nuts and position control ECU assembly.

      Tech Tips

      Use the same procedure to remove the position control ECU assembly on the other side.

  8. REMOVE REAR SEAT CLIMATE CONTROL ECU LH


    1. A01H0DD

      Disconnect the 2 connectors.

    2. Remove the 2 nuts and rear seat climate control ECU LH.

  9. REMOVE SEAT HEATER CONTROL SUB-ASSEMBLY


    1. Disconnect the connector.

    2. Detach the guide to remove the seat heater control sub-assembly.

      Tech Tips

      Use the same procedure to remove the seat heater control sub-assembly on the other side.

  10. REMOVE REAR SEAT COVER CAP LH


    1. A01H22F

      Detach the 5 claws to remove the rear seat cover cap LH.

  11. REMOVE REAR SEAT LOCK BASE LH


    1. A01H0K4

      Remove the 3 screws and rear seat lock base LH.

  12. REMOVE REAR SEATBACK COVER WITH PAD LH


    1. Remove the nut and detach the seatback cover bracket.

    2. Disconnect the connector.

    3. Detach the 8 hooks and remove the 19 hog rings and rear seatback cover with pad LH from the rear seatback spring assembly LH.

      A01H0KCE01
      Text in Illustration
      *1 Seatback Cover Bracket *2 Hook

  13. REMOVE SEPARATE TYPE REAR SEATBACK COVER LH


    1. A01H0L1

      Remove the 10 hog rings and separate type rear seatback cover LH from the rear seatback pad LH.

  14. REMOVE REAR SEATBACK CLIMATE CONTROL BLOWER LH

    A01GWHJE02
    Text in Illustration
    *1 Felt Pad

    1. Remove the felt pad.

    2. Disconnect the 3 connectors and detach the wire harness clamp.

    3. Remove the 3 nuts.

    4. Remove the 2 screws and rear seatback climate control blower LH.

  15. REMOVE REAR SEAT WIRE LH

    A01GXEE

    1. Disconnect the 3 connectors.

    2. Detach the 11 wire harness clamps to remove the rear seat wire LH.

  16. REMOVE REAR SEAT INNER BELT ASSEMBLY LH


    1. A01H1OOE01

      w/o Illumination:


      1. Remove the bolt and rear seat inner belt assembly LH.

    2. A01GX9A

      w/ Illumination:


      1. Disconnect the connector and detach the 2 clamps.

      2. A01H1J8E01

        Detach the clamp.

      3. Remove the bolt and rear seat inner belt assembly LH.

  17. REMOVE REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY LH

    A01GW6I

    1. Remove the nut and rear seat belt inner anchor bracket assembly LH.

  18. REMOVE SEAT CLIMATE CONTROL CONTROLLER LH


    1. A01GYB6

      Remove the rear No. 2 seat cushion pad.

    2. A01H0FQ

      Detach the 2 wire harness clamps and disconnect the 2 connectors.

    3. A01GXX7

      Remove the 2 screws.

    4. Detach the 2 claws to remove the seat climate control controller LH.

  19. REMOVE AIR FILTER

    A01GZQ4

    1. Detach the 2 claws to remove the air filter.

      Tech Tips

      Use the same procedure to remove the air filter on the other side.

  20. REMOVE REAR SEAT CLIMATE CONTROL BLOWER LH


    1. A01H06E

      Disconnect the connector.

    2. A01GWIC

      Remove the 3 nuts and rear seat climate control blower LH.

  21. REMOVE REAR SEAT CUSHION SPRING ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  22. REMOVE SEPARATE TYPE REAR SEAT CUSHION COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  23. REMOVE REAR SEAT SHOULDER BELT GUIDE RH

    Tech Tips

    Use the same procedures described for the LH side.

  24. REMOVE REAR SEAT CLIMATE CONTROL ECU RH

    Tech Tips

    Use the same procedures described for the LH side.

  25. REMOVE REAR SEAT COVER CAP RH

    Tech Tips

    Use the same procedures described for the LH side.

  26. REMOVE REAR SEAT LOCK BASE RH

    Tech Tips

    Use the same procedures described for the LH side.

  27. REMOVE REAR SEATBACK COVER WITH PAD RH

    Tech Tips

    Use the same procedures described for the LH side.

  28. REMOVE SEPARATE TYPE REAR SEATBACK COVER RH

    Tech Tips

    Use the same procedures described for the LH side.

  29. REMOVE REAR SEATBACK CLIMATE CONTROL BLOWER RH

    Tech Tips

    Use the same procedures described for the LH side.

  30. REMOVE REAR SEAT WIRE RH

    Tech Tips

    Use the same procedures described for the LH side.

  31. REMOVE REAR SEAT INNER BELT ASSEMBLY RH


    1. Use the same procedures described for the LH side.

  32. REMOVE REAR SEAT INNER CENTER BELT ASSEMBLY

    A01GYFV

    1. Remove the bolt and rear seat inner belt assembly center.

  33. REMOVE REAR SEAT BELT INNER ANCHOR BRACKET ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side.

  34. REMOVE SEAT CLIMATE CONTROL CONTROLLER RH

    Tech Tips

    Use the same procedures described for the LH side.

  35. REMOVE REAR SEAT CLIMATE CONTROL BLOWER RH

    Tech Tips

    Use the same procedures described for the LH side.

  36. REMOVE CENTER SEAT CUSHION COVER SUB-ASSEMBLY


    1. Remove the 23 hog rings.

    2. Detach the fastening tape to remove the center seat cushion cover from the center seat cushion pad with frame.

      A01GW4HE02
      Text in Illustration
      *1 Fastening Tape - -

  37. REMOVE REAR CENTER SEAT CUSHION PAD


    1. Remove the rear center seat cushion pad from the rear center seat cushion frame.

  38. REMOVE REAR CENTER SEAT HEADREST ASSEMBLY

    A01GYK9

    1. Remove the 2 bolts and rear center seat headrest assembly.

  39. REMOVE REAR SEAT ARMREST HOLE COVER


    1. A01GYDD

      Detach the 2 clips to remove the rear seat armrest hole cover.

  40. REMOVE CENTER SEATBACK FRAME SUB-ASSEMBLY

    A01GYLH

    1. Detach the wire harness clamp.

    2. Remove the 2 nuts and center seatback frame sub-assembly from the rear seat center armrest assembly.

  41. REMOVE TELEVISION SWITCH AND VOLUME ASSEMBLY


    1. Remove the television switch and volume assembly.

  42. REMOVE REAR NO. 1 SEAT CENTER ARMREST PANEL


    1. A01GW9ZE01

      Using moulding remover A, detach the 8 claws and 3 guides to remove the rear No. 1 seat center armrest panel together with the rear seat armrest hole board as indicated by the arrows in the order shown in the illustration.

    2. Disconnect the 2 connectors.

    3. A01H0QD

      Remove the 3 screws and rear No. 1 seat center armrest panel from the rear seat armrest hole board.

  43. REMOVE REAR POWER SEAT SWITCH


    1. A01GWNC

      Remove the 4 screws and rear power seat switch.

  44. REMOVE REAR SEAT CENTER ARMREST CUP HOLDER SUB-ASSEMBLY


    1. A01H0PX

      Remove the 2 screws and rear seat center armrest cup holder sub-assembly.

  45. REMOVE HEADPHONE TERMINAL


    1. Disconnect each connector.

    2. A01H183

      Using a moulding remover B, detach the 8 claws and remove the bezel.

    3. A01GXQ3

      Detach the 6 claws and remove the 2 headphone terminals.