FRONT SEAT ASSEMBLY REASSEMBLY

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.

Note

If the seat is set down in another location after removing it from the vehicle, the seat may tilt and damage the front seat adjuster assembly LH due to the difference in shape between the left and right seat tracks.

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

  • A bolt without a torque specification is shown in the standard bolt chart Click here.


  1. INSTALL FRONT SEAT WIRE LH


    1. Attach the 13 wire harness clamps to install the front seat wire LH.

    2. Connect the 4 connectors.

    3. Install the bolt.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }
      A01GYEN

  2. INSTALL SEAT POSITION AIRBAG SENSOR


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the battery negative (-) terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

    3. A01GW54E04

      Using a feeler gauge 1.0 mm (0.0393 in.), install the seat position sensor.

      Note


      • If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.

      • When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

      Tech Tips

      Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.0236 in.) to 1.4 mm (0.0551 in.).

    4. Using a T30 "TORX" socket wrench, install the "TORX" screw to install the seat position sensor.

      Torque:
      8.0 N*m  { 82 kgf*cm, 71 in.*lbf }

    5. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.0236 in.) to 1.4 mm (0.0551 in.).

    6. Check that there is no looseness in the installation parts of the seat position sensor.

    7. Connect the connector.

    8. Install the seat slide position sensor protector to the seat position sensor.

  3. INSTALL SEAT CLIMATE CONTROL BLOWER LH

    A01GYPS

    1. Install the climate control blower with the 2 bolts.

    2. Connect the connector and attach the wire harness clamps.

    3. Attach the 4 claws to connect the climate control duct.

  4. INSTALL NO. 1 AIR FILTER

    A01GX2B

    1. Rotate the air filter clockwise to attach the 4 claws to install it.

  5. INSTALL FRONT SEAT CLIMATE CONTROL ECU LH

    A01GYGQ

    1. Install the front seat climate control ECU LH with the 2 bolts.

    2. Connect the 2 connectors.

  6. INSTALL FRONT NO. 2 SEAT TRAVEL LINK

    A01H17H

    1. Install the front No. 2 seat travel link with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  7. INSTALL FRONT NO. 1 SEAT TRAVEL LINK

    Tech Tips

    Use the same procedures described for the front No. 2 seat travel link.

  8. INSTALL NO. 1 SEAT CUSHION PLATE

    A01GX31

    1. Install the No. 1 seat cushion plate with the 2 bolts.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }

  9. INSTALL FRONT SEAT CUSHION SPRING

    A01GXX8

    1. Install the front seat cushion spring.

      Tech Tips

      Use the same procedure to install the front seat cushion spring on the other side.

  10. INSTALL FRONT SEAT LOWER CUSHION SHIELD

    A01H1R3

    1. Install the front seat lower cushion shield with the 4 nuts.

  11. INSTALL RECLINING ADJUSTER INSIDE COVER LH

    A01H1S9

    1. Attach the wire harness clamp.

    2. Install the reclining adjuster inside cover LH with the screw.

  12. INSTALL RECLINING ADJUSTER INSIDE COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY LH (w/ Lumbar Support)


    1. Attach the 2 claws to install the lumbar support adjuster assembly LH.

    2. Rotate the snap in the direction indicated by the arrow in the illustration to attach the snap to the lumbar support adjuster assembly LH.

      Tech Tips

      Use the same procedure to attach the snap on the other side.

      A01GYJ2
    3. A01H28E

      Install the 4 bolts.

  14. INSTALL LUMBAR SUPPORT ADJUSTER ASSEMBLY RH (w/o Lumbar Support)


    1. Attach the 2 claws to install the lumbar support adjuster assembly RH.

    2. Rotate the snap in the direction indicated by the arrow in the illustration to attach the snap to the lumbar support adjuster assembly RH.

      Tech Tips

      Use the same procedure to attach the snap on the other side.

      A01GWXR
    3. A01H1UC

      Install the 2 bolts.

  15. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (BACK SIDE)


    1. A01GWWC

      Install the seat climate control controller LH with the 2 screws.

  16. INSTALL FRONT SEATBACK FRAME ASSEMBLY LH


    1. A01H1MM

      Temporarily install the front seatback frame assembly LH with the 4 bolts.

    2. Push the front seatback frame assembly LH towards the rear, and tighten the 4 bolts.

      Torque:
      43 N*m  { 439 kgf*cm, 32 ft.*lbf }

    3. for Driver Side:


      1. A01GXPN

        w/ Active Headrest:

        Attach the 9 clamps and connect the 4 connectors.

      2. A01GZX8

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 4 connectors.

    4. for Front Passenger Side:


      1. A01GWJC

        w/ Active Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      2. A01GXUO

        w/ Pre-crash Intelligent Headrest:

        Attach the 9 clamps and connect the 3 connectors.

      3. A01GYZL

        w/ Retractable Headrest:

        Attach the 7 clamps and connect the 2 connectors.

  17. INSTALL FRONT SEAT HEADREST ADJUSTER SUB-ASSEMBLY


    1. w/ Active Headrest:


      1. A01GX4N

        Attach the 2 claws.

      2. Install the headrest adjuster with the 2 bolts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }
      3. A01GWPY

        Connect the connector and attach the 2 wire harness clamps.

    2. w/ Pre-crash Intelligent Headrest:


      1. A01GXPQ

        Attach the 2 claws to connect the connector to the connector holder.

      2. A01H1L9

        Attach the guide to install the plate.

      3. Install the screw.

      4. A01GXLG

        Attach the 2 claws.

      5. Install the headrest adjuster with the 2 bolts.

        Torque:
        5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      6. Attach the 4 wire harness clamps.

      7. A01GWPY

        Connect the connector and attach the 2 wire harness clamps.

    3. w/ Retractable Headrest:


      1. A01GZUR

        Install the headrest stay cover with the 2 screws.

      2. A01GZJT

        Attach the 2 claws to install the cable.

      3. A01GYY2

        Attach the 2 claws to install the motor.

      4. A01H0KX

        Attach the 2 claws to install the headrest adjuster.

      5. Install the 4 bolts and 2 screws.

        Torque:
        21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  18. INSTALL FRONT SEAT HEADREST BRACKET (w/ Active Headrest)


    1. A01GZKZ

      Attach the wire harness clamp to install the front seat headrest bracket to the active headrest inflator.

  19. INSTALL ACTIVE HEADREST INFLATOR (w/ Active Headrest)


    1. A01GWE5E01
      Text in Illustration
      *1 Guide
      B Clamp

      Disconnect the connector.

      Note

      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. Remove the bolt and nut.

    3. Detach the guide and 2 clamps.

    4. Turn the active headrest inflator in the direction indicated by the arrow and remove it.

  20. INSTALL FRONT NO. 5 SEAT SET BRACKET (w/ Shoulder Switch)


    1. A01GX9N

      Attach the 2 clips to install the front No. 5 seat set bracket.

    2. Install the 2 screws.

  21. INSTALL SEPARATE TYPE FRONT SEATBACK COVER


    1. Set the separate type front seatback cover in place.

    2. for Sport Package:

      Attach the 4 pieces of fastening tape.

    3. Using hog ring pliers, install the separate type front seatback cover to the front seatback pad with 20 new hog rings as shown in the illustration.

      Note


      • Be careful not to damage the separate type front seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seatback cover.

      Tech Tips

      Install the hog rings at the cutouts.

      A01H1WXE01
      Text in Illustration
      *A except Sport Package *B for Sport Package
      *1 Fastening Tape *2 Hog Ring Plier

  22. INSTALL FRONT SEATBACK COVER WITH PAD


    1. Set the front seatback cover with pad in place.

    2. A01H120

      Attach the 9 hooks to install the front seatback cover with pad.

    3. Attach the 3 clips.

    4. A01GYQ4

      Attach the front seatback cover bracket with the bolt.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

  23. INSTALL POWER SEAT SWITCH ASSEMBLY (w/ Shoulder Switch)


    1. Connect the connector.

    2. A01GWDI

      Attach the 2 claws to install the power seat switch assembly.

  24. INSTALL FRONT SEAT HEADREST SUPPORT

    A01GZ16

    1. Attach the 4 claws to install the 2 front seat headrest supports.

  25. INSTALL FRONT SEAT HEADREST ASSEMBLY


    1. w/ Active Headrest, w/ Pre-crash Intelligent Headrest:


      1. A01GXHC

        Install the front seat headrest assembly with the 2 pins.

        Note

        w/ Active Headrest:

        When replacing a deployed active headrest inflator, always replace it together with the front seat headrest assembly.

    2. w/ Retractable Headrest:

      Install the front seat headrest assembly.

  26. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER


    1. Set the separate type front seat cushion cover in place.

    2. for Driver Side:


      1. A01GYNNE01
        Text in Illustration
        *1 Hog Ring Pliers

        except Sport Package:

        Using hog ring pliers, install the separate type front seat cushion cover to the front seat cushion pad with 21 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. A01GW6DE01
        Text in Illustration
        *1 Hog Ring Pliers

        for Sport Package:

        Using hog ring pliers, install the separate type front seat cushion cover to the front seat cushion pad with 17 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      3. A01GZ50

        Install the 2 clips.

    3. for Front Passenger Side:

      for Ottoman:


      1. A01H036E01
        Text in Illustration
        *1 Hog Ring Pliers

        Using hog ring pliers, install the separate type front seat cushion cover to the seat cushion pad with 21 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. A01H03U

        Install the 2 clips.

    4. for Front Passenger Side:

      except Ottoman:


      1. A01GWQJE01
        Text in Illustration
        *1 Hog Ring Pliers

        except Sport Package:

        Using hog ring pliers, install the separate type front seat cushion cover to the seat cushion pad with 21 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      2. A01H17FE01
        Text in Illustration
        *1 Hog Ring Pliers

        for Sport Package:

        Using hog ring pliers, install the separate type front seat cushion cover to the seat cushion pad with 17 new hog rings.

        Note


        • Be careful not to damage the separate type front seat cushion cover.

        • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type front seat cushion cover.

      3. A01H03U

        Install the 2 clips.

  27. INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH


    1. Attach the guide to install the seat heater control sub-assembly LH.

  28. INSTALL SEAT CUSHION COVER WITH PAD


    1. Set the front seat cushion cover with pad in place.

    2. for Driver Side:


      1. A01H28J

        Attach the 10 hooks to install the front seat cushion cover with pad.

      2. A01GWC6

        Attach the fastening tape.

      3. A01H0B4

        Install the 6 clips.

    3. for Front Passenger:

      for Ottoman:


      1. A01GYPM

        Attach the 10 hooks to install the front seat cushion cover with pad.

      2. A01GX6T

        Attach the fastening tape.

      3. A01GZRG

        Install the 6 clips.

    4. for Front Passenger:

      except Ottoman:


      1. A01GWYV

        Attach the 8 hooks to install the front seat cushion cover with pad.

    5. Connect the seat heater connector.

    6. A01H0B8

      Install the 2 clips.

  29. INSTALL SEAT CLIMATE CONTROL CONTROLLER LH (CUSHION SIDE)

    A01H025

    1. Install the seat climate control controller LH with the 2 screws.

  30. INSTALL FRONT SEAT CUSHION ASSEMBLY LH


    1. A01GWZDE01

      Install the front seat cushion assembly with the 4 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Attach the hook.

      Text in Illustration
      *1 Hook
    3. A01H21A

      Attach the hook.

    4. A01GYFU

      Install the 2 clips.

    5. A01GXIA

      Connect the connector and attach the 2 wire harness clamps.

    6. A01GYQ6

      Connect the connector and attach the wire harness clamp.

    7. A01GYQ8

      Connect the connector and attach the wire harness clamp.

    8. Attach the 4 claws to connect duct of the seat climate control blower LH.

    9. A01H1M8

      Connect the connector.

    10. A01GYWF

      Connect the duct of the seat climate control blower LH with the 3 screws.

    11. A01GYTY

      Attach the 2 claws to install the No. 6 air duct.

  31. INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY LH


    1. A01H1KT

      Install the No. 1 interior illumination light assembly LH with the screw.

    2. Attach the clamp.

  32. INSTALL FRONT SEATBACK BOARD SUB-ASSEMBLY LH


    1. A01H1Y4E01
      Text in Illustration
      *1 Hook
      *2 Wire Harness Clamp

      Connect the connector and attach the wire harness clamp.

    2. Attach the 2 hooks to install the front seatback board sub-assembly LH.

    3. Install the 2 screws.

  33. INSTALL FRONT SEAT INNER CUSHION SHIELD LH

    A01GW8J

    1. Attach the claw to install the front seat inner cushion shield LH.

    2. Install the 3 screws.

  34. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

    A01GX6QE02
    Text in Illustration
    *1 Protruding Part

    1. Install the front seat inner belt assembly LH with the nut.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

      Note

      Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding parts of the front seat adjuster.

    2. Attach the claw to connect the connector.

    3. Attach the 6 wire harness clamps.

    4. Connect the 2 connectors.

      A01GXDJE01
      Text in Illustration
      *A for Driver Side *B for Front Passenger Side

  35. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD LH (for Driver Side)


    1. A01H1UL

      Install the front seat inner No. 1 cushion shield LH with the 3 screws.

  36. INSTALL FRONT SEAT INNER NO. 1 CUSHION SHIELD RH (for Front Passenger Side)


    1. A01H0CQE01
      Text in Illustration
      *A for Ottoman
      *B except Ottoman

      Install the front seat inner No. 1 cushion shield RH with the 3 screws.

  37. INSTALL FRONT POWER SEAT SWITCH LH

    A01GWEH

    1. Install the front power seat switch LH with the 4 screws.

  38. INSTALL FRONT NO. 1 SEAT SHIELD SET BRACKET

    A01H0KO

    1. Install the front No. 1 seat shield set bracket with the 2 screws.

  39. INSTALL FRONT SEAT CUSHION SHIELD LH

    A01H1N9E01

    1. Connect the 2 connectors.

    2. Attach the 2 claws to install the front seat cushion shield LH as indicated by the arrows in the order shown in the illustration.

    3. Install the 3 screws.

    4. A01H14B

      Attach the rubber band of the front seatback board sub-assembly LH to the front seat adjuster assembly LH.