BACK WINDOW GLASS REMOVAL

Tech Tips

When removing the moulding, heat the vehicle body and moulding using a heat light.

Heating temperature

Item	Temperature
Vehicle Body	40 to 60°C (104 to 140°F)
Moulding	20 to 30°C (68 to 86°F)

Note

Do not heat the vehicle body and moulding excessively.

PRECAUTION

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.
REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)
REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)
REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)
1. Detach the 2 clips and remove the deck trim side board LH.

REMOVE BATTERY SERVICE HOLE COVER LH

Text in Illustration
*A	for Standard
*B	for Ottoman
*1	Fastening Tape

Detach the clip, fastening tape and remove the battery service hole cover LH.

DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.
REMOVE REAR SEAT ASSEMBLY
1. for Power Seat:
  
  Click here
2. for Ottoman:
  
  Click here
3. for Fixed Seat Type:
  
  Click here
REMOVE REAR DOOR SCUFF PLATE LH
1. for Standard Body:
  
  Click here
2. for Long Body:
  
  Click here
REMOVE REAR DOOR SCUFF PLATE RH
1. for Standard Body:
  
  Click here
2. for Long Body:
  
  Click here
REMOVE REAR SEAT SIDE GARNISH LH
1. Detach the 6 claws and remove the rear seat side garnish LH.
REMOVE REAR SEAT SIDE GARNISH RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE INNER ROOF SIDE GARNISH LH
Text in Illustration

*1 Clip A
1. Pull the inner roof side garnish LH away from the body to detach the 4 clips (do not detach clip A).
2. Detach the 2 claws of the guide, and pull the inner roof side garnish LH in the direction of the arrow to remove it.
  
  Tech Tips
  
  Clip A remains attached to the body.
3. Remove clip A from the vehicle body.
REMOVE INNER ROOF SIDE GARNISH RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY
1. except 4-Passenger with Ottoman:
  
  Using a moulding remover D, detach the 4 claws and remove the 3 belt guides.
2. for 4-Passenger with Ottoman:
  
  Using a moulding remover D, detach the 4 claws and remove the 2 belt guides.
3. except 4-Passenger with Ottoman:
  
  Detach the 2 clips of the package tray trim panel assembly. Then pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.
4. for 4-Passenger with Ottoman:
  
  Detach the 2 clips of the package tray trim panel assembly. Then pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.
5. Disconnect the solar sensor connector and remove the package tray trim panel.
REMOVE NO. 2 PACKAGE TRAY TRIM PANEL ASSEMBLY
1. Detach the 5 claws and 3 clips, and remove the No. 2 package tray trim panel assembly.
REMOVE ROOF CONSOLE BOX ASSEMBLY (w/ Rear Seat Entertainment System)
1. w/o Sliding Roof:
  1. Remove the 2 screws.
  2. Detach the 6 clips, 2 claws and 2 hooks and remove the roof console box assembly.
  3. Disconnect the connector.
2. w/ Sliding Roof:
  1. Remove the 2 screws.
  2. Detach the 6 clips and 2 hooks and remove the roof console box assembly.
  3. Disconnect the connector.
REMOVE SPOT LIGHT ASSEMBLY (w/o Rear Seat Entertainment System)
1. Using moulding remover D, detach the 4 claws and remove the spot light assembly.
2. Disconnect the connector.
REMOVE REAR VANITY LIGHT ASSEMBLY
Tech Tips

Use the same procedure to remove the vanity light on the other side.
1. Using a screwdriver, detach the 4 claws and remove the lens.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Remove the 2 screws.
3. Using moulding remover D, detach the claw and remove the vanity light assembly.
4. Disconnect the connector.
  
  Text in Illustration
  
  *1 Protective Tape - -
REMOVE COAT HOOK
Tech Tips

Use the same procedure to remove the hook on the other side.
1. Remove the screw and coat hook.
REMOVE ROOF SIDE REGISTER BEZEL LH (w/ Rear Cooler)
1. Remove the screw.
2. Detach the claw and remove the roof side register LH.
REMOVE ROOF SIDE REGISTER BEZEL RH (w/ Rear Cooler)

Tech Tips

Use the same procedure described for the LH side.
REMOVE ASSIST GRIP SUB-ASSEMBLY
Text in Illustration

*1 Protective Tape

Tech Tips

Use the same procedure for all the assist grips.
1. Using a screwdriver, detach the 4 claws and remove the 2 assist grip covers.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Detach the 2 clips and remove the assist grip sub-assembly.
REMOVE ROOF HEADLINING ASSEMBLY
1. for Standard Body:
  
  Tech Tips
  
  It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining Click here so that the back window glass can be removed in a later step.
2. for Long Body:
  
  Tech Tips
  
  It is not necessary to completely remove the roof headlining. Slightly lower the rear section of the roof headlining Click here so that the back window glass can be removed in a later step.
REMOVE AMPLIFIER ANTENNA ASSEMBLY
1. Disconnect each connector.
2. Detach the 4 clamps labeled A and remove the 2 nuts labeled B.
3. Detach the clip labeled C and remove the amplifier antenna.
  Tech Tips
  
  Remove the clip if it is damaged.
  
  The clip is used when the vehicle is assembled at the factory and is not needed for the reinstallation.
REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING LH
1. Put protective tape around the center roof drip side finish moulding.
2. for Standard Body:
  
  Using a moulding remover, detach the 16 clips and remove the center roof drip side finish moulding LH.
3. for Long Body:
  
  Using a moulding remover, detach the 17 clips and remove the center roof drip side finish moulding.
  Note
  
  Do not remove the clips from the vehicle body.
  
  If the clips are damaged or removed accidentally, replace them.
REMOVE CENTER ROOF DRIP SIDE FINISH MOULDING RH

Tech Tips

Use the same procedures described for the LH side.
REMOVE NO. 2 WINDSHIELD OUTSIDE MOULDING CLIP
Tech Tips

Perform the following procedure if replacing the No. 2 outside windshield moulding clip.
1. Remove the No. 2 outside windshield moulding clip.
2. Remove the No. 2 moulding clip.
REMOVE NO. 1 WINDSHIELD OUTSIDE MOULDING CLIP

Tech Tips

Use the same procedures described for the No. 2 windshield outside moulding clip.
REMOVE NO. 2 ROOF DRIP SIDE FINISH MOULDING CLIP
Tech Tips

Perform the following procedure if replacing the No. 2 roof drip side finish moulding clips.
1. Remove the 9 No. 2 roof drip side finish moulding clips.
REMOVE NO. 3 WINDSHIELD OUTSIDE MOULDING CLIP
Tech Tips

Perform the following procedure if replacing the No. 3 outside windshield moulding clip.
1. Put a 4 mm (0.16 in.) drill bit into a drill.
2. Wind tape around the drill bit approximately 5 mm (0.20 in.) from the tip of the drill.
  
  Tech Tips
  
  Tape the 4 mm (0.16 in.) drill bit to prevent the drill bit from going too deep.
3. Lightly press the drill against the rivets, drill off the flanges of the rivets, and remove the 10 rivets.
  Note
  
  Pressing the drill too firmly will cause the rivet to turn and result in the rivet not being drilled through.
  
  Do not pry the rivets with the drill, because this may cause damage to the installation holes of the rivets or the drill bit.
  
  Be careful of the drilled rivets as they may become hot.
  Text in Illustration
  
  *a Front Side *b Rear Side
4. Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
REMOVE NO. 1 ROOF DRIP SIDE FINISH MOULDING CLIP
Tech Tips

Perform the following procedure if replacing the No. 1 roof drip side finish moulding clips.
1. for Standard Body:
  
  Remove the 6 No. 1 roof drip side finish moulding clips.
2. for Long Body:
  
  Remove the 7 No. 1 roof drip side finish moulding clips.
REMOVE ROPE HOOK ASSEMBLY
1. Remove the 4 bolts and 4 rope hook assemblies.
REMOVE ROPE HOOK
1. Remove the 4 rope hooks by pushing the claws in the direction of the arrows in the illustration.

Text in Illustration
*1	Clip A

Text in Illustration
*1	Protective Tape	-	-

Text in Illustration
*1	Protective Tape

Text in Illustration
*a	Front Side	*b	Rear Side

REMOVE DECK TRIM SIDE BOARD RH

Text in Illustration
*A	w/ Spare Tire
*B	w/o Spare Tire

w/ Spare Tire:

Remove the clip.
Remove the deck trim side board RH.

w/o Spare Tire:
1. Detach the clip and remove the deck trim side board RH.

REMOVE NO. 1 LUGGAGE COMPARTMENT LIGHT ASSEMBLY
Text in Illustration

*1 Protective Tape
1. Using a screwdriver, detach the 2 claws and remove the No. 1 luggage compartment light assembly.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
2. Disconnect the connector.
REMOVE NO. 1 COOLER COVER (w/ Rear Cooler)
1. Detach the 5 clips and remove the No. 1 cooler cover.
REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER
1. Text in Illustration
  
  *A w/o Rear Cooler
  
  *B w/ Rear Cooler
  
  Remove the 3 clips.
2. Detach the 4 claws and remove the front luggage compartment trim cover.
REMOVE REAR FLOOR FINISH PLATE
1. Remove the 3 clips.
2. Detach the 4 clips and remove the rear floor finish plate.
REMOVE LOWER BACK WINDOW MOULDING OUTSIDE
1. Using a screwdriver, detach the 2 claws, 4 fasteners and double-sided tape (3 areas). Slide the moulding toward the front of the vehicle along the back window glass to detach the clip. Then remove the moulding.
  Note
  
  Be careful not to damage the vehicle body.
  
  Do not lift the moulding or slide it toward the rear of the vehicle when detaching the clip.
  
  The moulding is a non-reusable part.
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY LH
1. Remove the 2 clips.
2. Detach the claw and luggage compartment trim cover assembly LH.
REMOVE LUGGAGE COMPARTMENT TRIM COVER ASSEMBLY RH
1. Remove the 2 clips.
2. Detach the claw and luggage compartment trim cover assembly RH.

Text in Illustration
*1	Protective Tape

Text in Illustration
*A	w/o Rear Cooler
*B	w/ Rear Cooler

REMOVE REAR COMBINATION LIGHT ASSEMBLY LH

Put protective tape around the rear combination light assembly LH.
Disconnect the connector.
Remove the 3 nuts.

Move the rear combination light assembly LH in the direction of the arrow in the illustration, detach the clip, 2 claws and 2 guides to remove the rear combination light assembly LH.

Tech Tips

The clips remain on the vehicle body.

Text in Illustration
*1	Protective Tape	*2	Rear Combination Light Assembly LH
*3	Clip	-	-

REMOVE REAR COMBINATION LIGHT ASSEMBLY RH

Tech Tips

Use the same procedure described for the LH side.
REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER LH
1. Using a screwdriver, detach the double-sided tape (2 areas) and 2 clips. Then remove the hinge cover.
  Note
  
  If reusing the hinge cover, take care not to damage the hinge cover.
  
  Be careful not to damage the vehicle body.
  
  The hinge cover is a non-reusable part.
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE LUGGAGE COMPARTMENT DOOR HINGE COVER RH

Tech Tips

Use the same procedures described for the LH side.
REMOVE CENTER NO. 2 STOP LIGHT COVER
1. Push in the No. 2 center stop light cover at a point 10 mm (0.393 in.) from the end of the cover as shown in the illustration.
2. With the No. 2 center stop light cover pushed in, slide it towards the outside of the vehicle to detach the 4 claws.
3. Lift up the No. 2 center stop light cover to remove it as shown in the illustration.
REMOVE CENTER STOP LIGHT COVER
1. Push in the center stop light cover at a point 10 mm (0.393 in.) from the end of the cover as shown in the illustration.
2. With the center stop light cover pushed in, slide it towards the outside of the vehicle to detach the 4 claws.
3. Lift up the center stop light cover to remove it as shown in the illustration.
REMOVE CENTER STOP LIGHT CLIP
1. Turn the 2 center stop light clips 90° and remove them.
REMOVE CENTER STOP LIGHT ASSEMBLY
1. Disconnect the harness and connector.
2. Remove the 2 screws.
3. Detach the 2 claws and remove the center stop light assembly.
REMOVE BACK WINDOW GLASS
Note

As the stopper, bracket and harness are not supplied individually, be careful not to damage them when installing the back window glass.
1. Apply protective tape to the outer surface of the vehicle body to prevent scratches.
  
  Note
  
  When separating the back window glass from the vehicle, be careful not to damage the vehicle's paint or interior/exterior ornaments.
2. From the interior, insert a piano wire between the vehicle body and back window glass as shown in the illustration.
  Note
  
  If the stopper is damaged, the back window glass assembly must be replaced. Be careful when performing the procedure.
  
  Make sure not to deform the upper brackets.
  
  Make sure not to damage the wire harness.
3. Tie objects that can serve as handles (for example, wooden blocks) to both wire ends.
4. Place matchmarks over the glass and vehicle body on the locations indicated in the illustration.
  
  Tech Tips
  
  Matchmarks do not need to be placed if the glass is not going to be reused.
5. Cut through the adhesive by pulling the piano wire around the back window glass.
  
  Note
  
  Leave as much adhesive on the vehicle body as possible when removing the back window glass.
6. Using suction cups, remove the back window glass.
  
  Note
  
  If the stopper is damaged, the back window glass assembly must be replaced. Be careful when performing the procedure.
CLEAN BACK WINDOW GLASS
1. Clean the outer edge of the back window glass with a non-residue solvent.
  Note
  - Do not touch the back window glass surface after cleaning it.
  - Be careful not to damage the glass.
  - Even if using new back window glass, clean the back window glass with a non-residue solvent.
CLEAN VEHICLE BODY
1. Using a scraper, remove the moulding and adhesive from the back window glass.
2. Clean and shape the contact surface of the vehicle body.
  1. On the contact surface of the vehicle body, use a knife to cut away excess adhesive as shown in the illustration.
    
    Tech Tips
    
    Leave as much adhesive on the vehicle body as possible.
    
    Note
    
    Be careful not to damage the vehicle body.
  2. Clean the contact surface of the vehicle body with cleaner.
    
    Tech Tips
    
    Even if all the adhesive has been removed, clean the vehicle body.