POWER WINDOW REGULATOR MOTOR (for Rear Door) INSTALLATION

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.


  1. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. A01H00O

      Apply MP grease to the sliding and rotating areas of the rear power window regulator motor assembly.

    2. Using a T25 ''TORX'' driver, install the rear power window regulator motor assembly with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  2. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. A01GZ8CE04
      Text in Illustration
      *1 Temporary Bolt

      Apply MP grease to the sliding and rotating areas of the rear door window regulator sub-assembly LH.

    2. Temporary install the temporary bolt to the rear door window regulator sub-assembly LH.

    3. Install the rear door window regulator sub-assembly LH with the 3 bolts, and then tighten the temporary bolt.

      Torque:
      11 N*m  { 115 kgf*cm, 8 ft.*lbf }

      Note

      be careful not to drop the window regulator as it may become damaged

    4. Connect the connector.

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Note

    Be careful not to drop and deform the rear door window regulator.


    1. Install the rear door glass sub-assembly LH with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Tech Tips


      • Insert a cloth inside the door panel to prevent the door glass from being scratched.

      • Position the door glass toward the front as much as possible.

    2. Install the hole plug.

  4. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. A01GZIY

      Install the rear door quarter glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.

  5. INSTALL REAR DOOR GLASS RUN LH


    1. Install the rear door glass run LH to the division bar assembly.

  6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. Install the rear door window division bar sub-assembly LH with the 2 nuts.

  7. INSTALL REAR DOOR DIVISION BAR LOWER BRACKET LH


    1. Install the 3 nuts and rear door division bar lower bracket LH bracket to the door panel.

  8. INSTALL REAR DOOR SERVICE HOLE COVER LH


    1. Apply new butyl tape to the door.

    2. A01GYXFE01
      Text in Illustration
      *a Reference Point

      Install a new rear door service hole cover LH using the reference points on the rear door panel.

      Tech Tips


      • When installing the service hole cover, pull the links and connectors through the service hole cover.

      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the sealing quality.

  9. INSTALL REAR DOOR GLASS INNER WEATHERSTRIP LH


    1. for Long Body:


      1. Install the rear door glass inner weatherstrip LH to the door panel.

    2. for Standard Body:


      1. Install the rear door glass inner weatherstrip LH to the door panel.

  10. INSTALL REAR SIDE TRIM BOARD COVER LH (w/ Rear Door Sunshade)


    1. Install the rear side trim board cover LH with the 2 screws.

  11. INSTALL NO. 1 AUTO CURTAIN RAIL BRACKET LH (w/ Rear Door Sunshade)


    1. Attach the clip to install the No. 1 auto curtain rail bracket LH.

  12. INSTALL REAR CURTAIN SUB-ASSEMBLY LH (w/ Rear Door Sunshade)


    1. for Standard Body:


      1. Connect the connector.

      2. Attach the 3 clips to install the rear curtain sub-assembly LH.

      3. Install the 10 screws.

    2. for Long Body:


      1. Connect the connector.

      2. Attach the 4 clips to install the rear curtain sub-assembly LH.

      3. Install the 10 screws.

  13. INSTALL REAR DOOR NO. 2 FRAME GARNISH LH


    1. Attach the claws and install the rear door No. 2 frame garnish LH.

  14. INSTALL REAR DOOR FRAME GARNISH LH


    1. w/o Rear Door Sunshade:


      1. Attach the claws.

      2. Attach the clip to install the rear door frame garnish LH with screw.

    2. w/ Rear Door Sunshade:


      1. Attach the claws.

      2. Attach the 2 clips to install the rear door frame garnish LH.

  15. INSTALL REAR DOOR TRIM COVER LH


    1. Attach the 5 clips to install the rear door trim cover LH.

    2. Install the cushion.

  16. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. w/o Rear Door Sunshade

      Click here

    2. w/ Rear Door Sunshade:

      Click here

  17. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

    A01GXK8

    1. Install the illumination light with the screw.

    2. Connect the connector.

    3. Attach the 2 clips to install the rear power window regulator switch assembly with rear door armrest base panel.

  18. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. Attach the 3 claws to install the rear door inside handle bezel plug LH.

  19. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  20. INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman

      Attach the battery service hole cover LH with the clip and fastening tape.

  21. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  22. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  23. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI