POWER WINDOW REGULATOR MOTOR (for Front Door) INSTALLATION

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.


  1. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH


    1. A01GY5R

      Apply MP grease to the sliding and rotating areas of the regulator motor.

    2. Using a T25 ''TORX'' driver, install the motor with the 3 screws.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  2. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH


    1. A01GZ1NE05
      Text in Illustration
      *1 Temporary Bolt

      Apply MP grease to the sliding and rotating area of the front door window regulator sub-assembly LH.

      Note

      Do not apply grease to the spring of the window regulator.

    2. Temporarily install the temporary bolt to the front door window regulator sub-assembly LH.

    3. Install the window regulator with the 5 bolts and tighten the temporary bolt.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

      Note

      Be careful not to drop the window regulator as it may become damaged.

    4. Connect the connector.

  3. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. A01GW9LE02

      Insert the front door glass sub-assembly LH into the door panel along the glass run as indicated by the arrows in the illustration.

      Note

      Be careful not to damage the glass.

    2. Install the front door glass sub-assembly LH to the front door window regulator sub-assembly LH with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

    3. Install the hole plug.

  4. INSTALL FRONT DOOR SERVICE HOLE COVER LH


    1. Apply new butyl tape to the door.

    2. A01H0BWE01
      Text in Illustration
      *a Reference Point

      Install a new front door service hole cover LH using the reference points on the front door panel.

      Tech Tips


      • When installing the service hole cover, pull the links and connectors through the service hole cover.

      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the sealing quality.

  5. INSTALL DOOR FRAME GARNISH LH


    1. Install the door frame garnish LH with the 2 clips.

  6. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. Connect the connector.

    2. A01GXAA

      Connect the 2 cables to the inside handle.

    3. Attach the 13 clips to install the front door trim board sub-assembly LH.

    4. Install the 3 screws.

  7. INSTALL POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for LHD)


    1. A01GX6M

      Connect the connector.

    2. Install the power window regulator master switch assembly.

  8. INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for RHD)


    1. A01GZQY

      Connect the 2 connectors.

    2. Install the front power window regulator switch assembly.

  9. INSTALL FRONT DOOR INSIDE HANDLE BEZEL PLUG LH


    1. Attach the 3 claws to install the front door inside handle bezel plug LH.

  10. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  11. INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman

      Attach the battery service hole cover LH with the clip and fastening tape.

  12. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  13. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  14. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.