CIGARETTE LIGHTER (for Instrument Panel Side) REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

    A01GX53

    1. Pull the front part of the instrument panel finish panel end LH to detach the 6 clips.

    2. Pull the instrument panel finish panel end LH to detach 3 clips and remove the instrument panel finish panel end LH.

  2. REMOVE INSTRUMENT PANEL FINISH PANEL END RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY

    A01GZOF

    1. Twist the shift lever knob sub-assembly in the direction indicated by the arrow and remove it.

  4. REMOVE NO. 3 BOX PANEL

    A01H20I

    1. Detach the 4 claws and remove the No. 3 box panel.

  5. REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY

    A01H0JQE01
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Move the shift lever to N.

    3. Remove the 2 screws.

    4. Detach the 6 clips and remove the upper rear console panel sub-assembly.

    5. Disconnect each connector and detach each wire harness clamp.

  6. REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL


    1. Apply protective tape as shown in the illustration.

    2. Hold the opposite end with one hand as shown in the illustration so that the clip can be firmly pushed.

    3. Insert a screwdriver at the location shown in the illustration, and then push the lower clip on the backside of the upper instrument cluster finish panel towards the rear of the vehicle to detach it.

      Note

      At this time, all the clips may become detached and the upper instrument cluster finish panel may suddenly come off. Therefore, slowly push on the clip to detach it.

      Tech Tips


      • Tape the screwdriver tip before use.

      • The upper clip of the upper instrument cluster finish panel may become detached at the same time.

      A01GYB8E01
      Text in Illustration
      *1 Protective Tape *2 Lower Clip
      A01GYOB Rear of the Vehicle - -

    4. Insert a screwdriver at the location shown in the illustration, and then push the lower clip on the backside of the upper instrument cluster finish panel towards the rear of the vehicle to detach it.

      Note


      • Slowly push on the clip to detach it.

      • At this time, all the clips may become detached and the upper instrument cluster finish panel may suddenly come off. Therefore, place one hand on the upper instrument cluster finish panel as shown in the illustration.

      Tech Tips


      • Tape the screwdriver tip before use.

      • The upper clip of the upper instrument cluster finish panel may become detached at the same time.

      A01GX7OE01
      Text in Illustration
      *1 Protective Tape *2 Lower Clip
      A01GYOB Rear of the Vehicle - -
    5. A01GX5SE01
      Text in Illustration
      *1 Protective Tape
      A01GYAG Upper Instrument Cluster Finish Panel Edge

      Insert moulding remover A between the upper instrument cluster finish panel and lower No. 1 instrument panel finish panel, and between the upper instrument cluster finish panel and lower No. 2 instrument panel finish panel to detach the 3 upper clips and remove the upper instrument cluster finish panel.

      Note

      If pressure is applied to the edge of the upper instrument cluster finish panel using moulding remover A, the surface may be damaged. Therefore, insert moulding remover A deep past the edge of the upper instrument cluster finish panel to detach the clips.

      Tech Tips

      If any of the upper clips have become detached during the previous procedure, detach the remaining clips to remove the upper instrument cluster finish panel.

  7. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Disconnect the connector.

    2. A01GYML

      Detach the 6 clips and remove the upper console panel sub-assembly.

  8. REMOVE CIGARETTE LIGHTER COVER


    1. A01GYA7

      Disconnect the connector and detach the wire harness clamp.

    2. A01H0YG

      Using a screwdriver, release the lock and remove the wire harness clamp from the connector.

    3. A01H0AQ

      Detach the 2 claws and remove the cigarette lighter cover.

  9. REMOVE CIGARETTE LIGHTER ASSEMBLY


    1. Remove the cigarette lighter knob and element assembly.

    2. A01H0J5

      Using a screwdriver, detach the claw and cigarette lighter socket.

  10. REMOVE CIGARETTE LIGHTER BEZEL STAY

    A01GWD6

    1. Detach the 2 claws and remove the cigarette lighter bezel stay from the upper console panel sub-assembly.