Click here

CLOCK REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

Click here
  1. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

  2. Click here

    REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

  3. Click here

    REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  4. Click here

    REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02

      Detach the clip, fastening tape and remove the battery service hole cover LH.

      Table 1. Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape
  5. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery negative (-) terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery negative (-) terminal notices before proceeding with work (Click here).

  6. Click here

    DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  7. Click here

    REMOVE INSTRUMENT PANEL FINISH PANEL END LH


    1. Pull the front part of the instrument panel finish panel end LH to detach the 6 clips.

    2. Pull the instrument panel finish panel end LH to detach 3 clips and remove the instrument panel finish panel end LH.

  8. Click here

    REMOVE INSTRUMENT PANEL FINISH PANEL END RH

    Tip:

    Use the same procedure described for the LH side.

  9. Click here

    REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY


    1. Twist the shift lever knob sub-assembly in the direction indicated by the arrow and remove it.

  10. Click here

    REMOVE NO. 3 BOX PANEL


    1. Detach the 4 claws and remove the No. 3 box panel.

  11. Click here

    REMOVE UPPER REAR CONSOLE PANEL SUB-ASSEMBLY


    1. Apply protective tape as shown in the illustration.

      Table 2. Text in Illustration
      *1 Protective Tape

    2. Move the shift lever to N.

    3. Remove the 2 screws.

    4. Detach the 6 clips and remove the upper rear console panel sub-assembly.

    5. Disconnect each connector and detach each wire harness clamp.

  12. Click here

    REMOVE UPPER INSTRUMENT CLUSTER FINISH PANEL


    1. Apply protective tape as shown in the illustration.

    2. Hold the opposite end with one hand as shown in the illustration so that the clip can be firmly pushed.

    3. A01GYB8E01

      Insert a screwdriver at the location shown in the illustration, and then push the lower clip on the backside of the upper instrument cluster finish panel towards the rear of the vehicle to detach it.

      Note:

      At this time, all the clips may become detached and the upper instrument cluster finish panel may suddenly come off. Therefore, slowly push on the clip to detach it.

      Tip:

      • Tape the screwdriver tip before use.

      • The upper clip of the upper instrument cluster finish panel may become detached at the same time.

      Table 3. Text in Illustration
      *1 Protective Tape *2 Lower Clip
      A01GYOB Rear of the Vehicle - -
    4. A01GX7OE01

      Insert a screwdriver at the location shown in the illustration, and then push the lower clip on the backside of the upper instrument cluster finish panel towards the rear of the vehicle to detach it.

      Note:

      • Slowly push on the clip to detach it.

      • At this time, all the clips may become detached and the upper instrument cluster finish panel may suddenly come off. Therefore, place one hand on the upper instrument cluster finish panel as shown in the illustration.

      Tip:

      • Tape the screwdriver tip before use.

      • The upper clip of the upper instrument cluster finish panel may become detached at the same time.

      Table 4. Text in Illustration
      *1 Protective Tape *2 Lower Clip
      A01GYOB Rear of the Vehicle - -
    5. A01GX5SE01

      Insert moulding remover A between the upper instrument cluster finish panel and lower No. 1 instrument panel finish panel, and between the upper instrument cluster finish panel and lower No. 2 instrument panel finish panel to detach the 3 upper clips and remove the upper instrument cluster finish panel.

      Note:

      If pressure is applied to the edge of the upper instrument cluster finish panel using moulding remover A, the surface may be damaged. Therefore, insert moulding remover A deep past the edge of the upper instrument cluster finish panel to detach the clips.

      Table 5. Text in Illustration
      *1 Protective Tape
      A01GYAG Upper Instrument Cluster Finish Panel Edge
      Tip:

      If any of the upper clips have become detached during the previous procedure, detach the remaining clips to remove the upper instrument cluster finish panel.

  13. Click here

    REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    1. Disconnect the connector.

    2. A01GYML

      Detach the 6 clips and remove the upper console panel sub-assembly.

  14. Click here

    REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL


    1. Detach the 4 clips and 5 guides and remove the lower No. 1 instrument panel finish panel.

    2. Disconnect the connector.

  15. Click here

    REMOVE LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL


    1. Detach the 4 clips and 5 guides and remove the lower No. 2 instrument panel finish panel.

  16. Click here

    REMOVE MULTI-MEDIA MODULE RECEIVER ASSEMBLY


    1. A01GWQ1

      Remove the 2 bolts.

    2. Detach the 6 clips and pull out the multi-media module receiver assembly with bracket.

    3. Disconnect the connectors and remove the multimedia module receiver assembly with bracket.

  17. Click here

    REMOVE INSTRUMENT SIDE PANEL RH


    1. Apply protective tape as shown in the illustration.

      Table 6. Text in Illustration
      *1 Protective Tape

    2. Using moulding remover D, detach the 6 clips and remove the instrument side panel RH.

  18. Click here

    REMOVE INSTRUMENT CLUSTER FINISH PANEL GARNISH ASSEMBLY


    1. Apply protective tape as shown in the illustration.

    2. Using moulding remover B, detach the 12 clips and remove the instrument cluster finish panel garnish assembly.

    3. A01GWEDE01

      Disconnect each connector.

      Table 7. Text in Illustration
      *1 Protective Tape - -
  19. Click here

    REMOVE CLOCK ASSEMBLY


    1. Disconnect the connector.

    2. Using a screwdriver, detach the 2 claws and remove the clock assembly from the instrument cluster finish panel garnish assembly.

      Tip:

      Tape the screwdriver tip before use.

      Table 8. Text in Illustration
      *1 Protective Tape