PARKING ASSIST MONITOR SYSTEM Image from Camera for Parking Assist Monitor is Abnormal

DESCRIPTION

The video signal from the television camera assembly is transmitted to the accessory meter assembly via the multi-media module receiver assembly.

WIRING DIAGRAM

A01H1UBE04

INSPECTION PROCEDURE

Note


  • When "System initializing" is displayed on the accessory meter assembly after disconnecting the cable from the negative (-) auxiliary battery terminal, correct the steering angle neutral point Click here.

  • Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed Click here.

Tech Tips

Images may be unclear even in normal conditions if:


  • Noise may occur in the image depending on electrical devices used in the cabin.

  • Noise may occur in the image if accessories that generate radio waves have been installed.

  • The camera screen is frosted over (the image immediately after turning the power switch on (IG) may be blurred or darker than normal).

  • The camera lens is dirty with snow, mud, etc.

  • A strong beam of light, such as a sunbeam or headlight, hits the camera.

  • It is too dark around the camera (at night etc.).

  • The ambient temperature around the camera is either too high or too low.

  • The vehicle is tilted at a steep angle.

  • When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.

PROCEDURE


  1. CHECK NAVIGATION SYSTEM OR AUDIO AND VISUAL SYSTEM


    1. w/o Navigation System

      Check the operation of the audio and visual system Click here.

    2. w/ Navigation System

      Check the operation of the audio and visual system Click here.

      Result
      Result Proceed to
      System operates normally A
      System does not operates normally (w/o Navigation System) B
      System does not operates normally (w/ Navigation System) C

    B

    GO TO AUDIO AND VISUAL SYSTEM Click here

    C

    GO TO NAVIGATION SYSTEM Click here

    A

  2. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - LUGGAGE ELECTRICAL KEY SWITCH AND BODY GROUND)


    1. Disconnect the L164 multi-media module receiver assembly connector.

    2. Disconnect the S101 luggage electrical key switch connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L164-12 (GND1) - Body ground Always Below 1 Ω
      L164-18 (V+) - S101-7 (CV+) Always Below 1 Ω
      L164-19 (V-) - S101-2 (CV-) Always Below 1 Ω
      L164-39 (CA+) - S101-6 (CB+) Always Below 1 Ω
      L164-40 (CGND) - S101-1 (CGND) Always Below 1 Ω
      L164-18 (V+) - Body ground Always 10 kΩ or higher
      L164-19 (V-) - Body ground Always 10 kΩ or higher
      L164-39 (CA+) - Body ground Always 10 kΩ or higher
      L164-40 (CGND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CA+, CGND)


    1. A01H13JE46
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      Reconnect the multi-media module receiver assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L164-40 (CGND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L164-39 (CA+) - L164-40 (CGND) Power switch on (READY), shift lever in R 5.5 to 7.05 V

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

  4. CHECK TELEVISION CAMERA ASSEMBLY (CV+, CGND)


    1. Reconnect the S101 television camera assembly connector.

      A01GX4LE08
      Text in Illustration
      *a

      Component with harness connected

      (Multi-media Module Receiver Assembly)

      		 *b Waveform A
      *c Waveform B *d Synchronization Signal
      *e Video Waveform - -

    2. Check the waveform of the television camera assembly using an oscilloscope.

      Item Content
      Terminal No. (Symbol) L164-18 (V+) - L164-40 (CGND)
      Tool Setting 0.2 V/DIV., 50 μs/DIV.
      Condition

      Waveform A: Power switch on (READY), shift lever in R (camera lens is not covered, displaying an image)

      Waveform B: Power switch on (READY), shift lever in R (camera lens is covered, blacking out the screen)

      Tech Tips

      The video waveform changes according to the image sent by the television camera assembly.

      OK
      Waveform is as shown in the illustration.

    NG

    Click here

    OK

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

  5. CHECK LUGGAGE ELECTRICAL KEY SWITCH (CAMERA CIRCUIT)

    A01GYQ7E08
    Text in Illustration
    *a

    Front view of Luggage Electrical Key Switch

    (Wire Harness Side)

    		 *b

    Front view of Luggage Electrical Key Switch

    (Television Camera Assembly Side)

    1. Disconnect the luggage electrical key switch connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      S101-1 (CGND) - A-5 (CGND) Always Below 1 Ω
      S101-1 (CGND) - A-1 (CURT) Always Below 1 Ω
      S101-2 (CV-) - A-2 (CV-) Always Below 1 Ω
      S101-6 (CB+) - A-6 (CB+) Always Below 1 Ω
      S101-7 (CV+) - A-3 (CV+) Always Below 1 Ω
      S101-1 (CGND) - Body ground Always 10 kΩ or higher
      S101-2 (CV-) - Body ground Always 10 kΩ or higher
      S101-6 (CB+) - Body ground Always 10 kΩ or higher
      S101-7 (CV+) - Body ground Always 10 kΩ or higher

    NG

    REPLACE LUGGAGE ELECTRICAL KEY SWITCH Click here

    OK

    REPLACE TELEVISION CAMERA ASSEMBLY Click here