NAVIGATION SYSTEM AVC-LAN Circuit

DESCRIPTION

Each audio system component connected to the AVC-LAN (communication bus) transfers switch signals using the audio visual communication local area network.

If a short to +B or short to ground occurs in the AVC-LAN, the audio system will not function normally because communication is not possible.

WIRING DIAGRAM

A01GYMZE05

INSPECTION PROCEDURE

Note

Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System Click here.

PROCEDURE


  1. INSPECT MULTI-MEDIA MODULE RECEIVER ASSEMBLY


    1. A01GYZOE21

      Remove the multi-media module receiver assembly with the connector(s) still connected Click here.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      45 (TX3+) - 46 (TX3-) Always 60 to 80 Ω

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (AVC-LAN CIRCUIT)


    • *1: for 4-passenger with Ottoman

    • *2: except 4-passenger with Ottoman

    • *3: w/ Audio Switch


    1. Disconnect the L164 multi-media module receiver assembly connector.

    2. Disconnect the L163 accessory meter assembly connector.

    3. Disconnect the L161 clock assembly connector.

    4. Disconnect the S15*1 or z54*2 rear power seat switch (audio switch) connector.*3

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L164-45 (TX3+) - L163-7 (TX+) Always Below 1 Ω
      L164-46 (TX3-) - L163-19 (TX-) Always Below 1 Ω
      L161-3 (TX+1) - L163-5 (TX2+) Always Below 1 Ω
      L161-2 (TX-1) - L163-17 (TX2-) Always Below 1 Ω
      S15-4 (TX+) - L163-6 (TX1+)*1,*3 Always Below 1 Ω
      S15-3 (TX-) - L163-18 (TX1-)*1,*3 Always Below 1 Ω
      z54-10 (TX+) - L163-6 (TX1+)*2,*3 Always Below 1 Ω
      z54-11 (TX-) - L163-18 (TX1-)*2,*3 Always Below 1 Ω
      L164-45 (TX3+) - Body ground Always 10 kΩ or higher
      L164-46 (TX3-) - Body ground Always 10 kΩ or higher
      L161-3 (TX+1) - Body ground Always 10 kΩ or higher
      L161-2 (TX-1) - Body ground Always 10 kΩ or higher
      S15-4 (TX+) - Body ground*1,*3 Always 10 kΩ or higher
      S15-3 (TX-) - Body ground*1,*3 Always 10 kΩ or higher
      z54-10 (TX+) - Body ground*2,*3 Always 10 kΩ or higher
      z54-11 (TX-) - Body ground*2,*3 Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT MALFUNCTIONING PARTS


    1. Disconnect and reconnect each slave unit one by one until the master unit returns to normal operation.

      Tech Tips


      • Check all slave units.

      • When disconnecting a slave unit causes the master unit to return to normal operation, this indicates that the slave unit is malfunctioning. Replace the malfunctioning slave unit.

      OK
      Master unit returns to normal operation.

    NG

    REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY Click here

    OK

    REPLACE MALFUNCTIONING PARTS