AUDIO AND VISUAL SYSTEM Illumination Circuit

DESCRIPTION

Power is supplied to the multi-media module receiver assembly, accessory meter assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM

A01GZ2FE02

INSPECTION PROCEDURE

Note


  • The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System Click here.

  • Inspect the fuse for circuits related to this system before performing the following inspection procedure.

PROCEDURE


  1. CHECK ILLUMINATION


    1. Check if the illumination for the multi-media module receiver assembly, accessory meter assembly, steering pad switch assembly or others (hazard switch etc.) comes on when the light control switch is turned to the head or tail position.

      Result
      Result Proceed to
      Illumination comes on for all components except steering pad switch assembly. A
      Illumination comes on for all components except accessory meter assembly. B
      Illumination comes on for all components except multi-media module receiver assembly. C
      No illumination comes on (multi-media module receiver assembly, accessory meter assembly, steering pad switch, hazard switch, heater control switch, etc.). D

    B

    CHECK HARNESS AND CONNECTOR (ACCESSORY METER ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND) Click here

    C

    CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - NO. 1 METER ECU SUB-ASSEMBLY AND AUXILIARY BATTERY) Click here

    D

    GO TO LIGHTING SYSTEM Click here

    A

  2. CHECK STEERING PAD SWITCH ASSEMBLY


    1. Temporarily replace the steering pad switch assembly with a new or normally functioning one Click here.

    2. Check if the same malfunction recurs.

      Result
      Result Proceed to
      Malfunction does not recur (returns to normal). A
      Malfunction recurs. B

    B

    INSPECT SPIRAL CABLE SUB-ASSEMBLY Click here

    A

    END (STEERING PAD SWITCH ASSEMBLY IS DEFECTIVE)

  3. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. Remove the spiral cable sub-assembly Click here.

    2. Inspect the spiral cable sub-assembly Click here.


    NG

    REPLACE SPIRAL CABLE SUB-ASSEMBLY Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - NO. 1 METER ECU SUB-ASSEMBLY AND AUXILIARY BATTERY)


    1. Disconnect the L126 spiral cable sub-assembly connector.

    2. Disconnect the L124 No. 1 meter ECU sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L126-14 (ILL-) - L124-16 (ILL-) Always Below 1 Ω
      L126-14 (ILL-) - Body ground Always 10 kΩ or higher

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      L126-7 (+B) - Body ground Always 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  5. CHECK HARNESS AND CONNECTOR (ACCESSORY METER ASSEMBLY - AUXILIARY BATTERY AND BODY GROUND)


    1. A01H0A5E40
      Text in Illustration
      *a

      Front view of wire harness connector

      (to Accessory Meter Assembly)

      Disconnect the L163 accessory meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L163-13 (GND1) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L163-2 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  6. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - NO. 1 METER ECU SUB-ASSEMBLY AND AUXILIARY BATTERY)


    1. Disconnect the L164 multi-media module receiver assembly connector.

    2. Disconnect the L124 No. 1 meter ECU sub-assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      L164-13 (ILL-) - L124-16 (ILL-) Always Below 1 Ω
      L164-13 (ILL-) - Body ground Always 10 kΩ or higher

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      L164-14 (ILL+) - Body ground Light control switch in the tail or head position 11 to 14 V

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

    PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE Click here