ENTRY LOCK AND UNLOCK SWITCH (for Rear) INSTALLATION

Tech Tips


  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.


  1. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH


    1. Insert the front end of the rear door outside handle assembly LH into the rear door outside handle frame.

      Note

      If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and it will damage the release plate.

    2. Connect the connector.

    3. Using a T30 ''TORX'' socket, tighten the screw.

  2. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH


    1. Using a T30 ''TORX'' socket, install the rear door outside handle cover LH with the screw.

  3. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

    Note

    Be careful not to drop and deform the rear door window regulator.


    1. Install the rear door glass sub-assembly LH with the 2 bolts.

      Torque:
      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

      Tech Tips


      • Insert a cloth inside the door panel to prevent the door glass from being scratched.

      • Position the door glass toward the front as much as possible.

    2. Install the hole plug.

  4. INSTALL REAR DOOR QUARTER WINDOW GLASS LH


    1. A01GZIY

      Install the rear door quarter glass LH together with the rear door quarter window weatherstrip LH in the direction indicated by the arrow in the illustration.

  5. INSTALL REAR DOOR GLASS RUN LH


    1. Install the rear door glass run LH to the division bar assembly.

  6. INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH


    1. Install the rear door window division bar sub-assembly LH with the 2 nuts.

  7. INSTALL REAR DOOR DIVISION BAR BRACKET LOWER LH


    1. Install the 3 nuts and rear door division bar lower bracket LH bracket to the door panel.

  8. INSTALL REAR DOOR SERVICE HOLE COVER LH


    1. Apply new butyl tape to the door.

    2. A01GYXFE01
      Text in Illustration
      *a Reference Point

      Install a new rear door service hole cover LH using the reference points on the rear door panel.

      Tech Tips


      • When installing the service hole cover, pull the links and connectors through the service hole cover.

      • There should be no wrinkles or folds after attaching the service hole cover.

      • After attaching the service hole cover, check the sealing quality.

  9. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH


    1. for Long Body:


      1. Install the rear door glass inner weatherstrip LH to the door panel.

    2. for Standard Body:


      1. Install the rear door glass inner weatherstrip LH to the door panel.

  10. INSTALL REAR SIDE TRIM BOARD COVER LH (w/ Rear Door Sunshade)


    1. Install the rear side trim board cover LH with the 2 screws.

  11. INSTALL NO. 1 AUTO CURTAIN RAIL BRACKET LH (w/ Rear Door Sunshade)


    1. Attach the clip to install the No. 1 auto curtain rail bracket LH.

  12. INSTALL REAR LH CURTAIN SUB-ASSEMBLY (w/ Rear Door Sunshade)


    1. for Standard Body:


      1. Connect the connector.

      2. Attach the 3 clips to install the rear curtain sub-assembly LH.

      3. Install the 10 screws.

    2. for Long Body:


      1. Connect the connector.

      2. Attach the 4 clips to install the rear curtain sub-assembly LH.

      3. Install the 10 screws.

  13. INSTALL REAR DOOR NO. 2 FRAME GARNISH LH


    1. Attach the claws and install the rear door No. 2 frame garnish LH.

  14. INSTALL REAR DOOR FRAME GARNISH LH


    1. w/o Rear Door Sunshade:


      1. Attach the claws.

      2. Attach the clip to install the rear door frame garnish LH with screw.

    2. w/ Rear Door Sunshade:


      1. Attach the claws.

      2. Attach the 2 clips to install the rear door frame garnish LH.

  15. INSTALL REAR DOOR TRIM COVER LH


    1. Attach the 5 clips to install the rear door trim cover LH.

    2. Install the cushion.

  16. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. w/o Rear Door Sunshade:

      Click here

    2. w/ Rear Door Sunshade

      Click here

  17. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

    A01GXK8

    1. Install the illumination light with the screw.

    2. Connect the connector.

    3. Attach the 2 clips to install the rear power window regulator switch assembly with rear door armrest base panel.

  18. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH


    1. Attach the 3 claws to install the rear door inside handle bezel plug LH.

  19. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  20. INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman

      Attach the battery service hole cover LH with the clip and fastening tape.

  21. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  22. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  23. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI