REAR SEAT OUTER BELT ASSEMBLY REMOVAL


  1. PRECAUTION

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work Click here.

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  3. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  4. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  5. REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape

      Detach the clip, fastening tape and remove the battery service hole cover LH.

  6. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the auxiliary battery negative (-) terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. REMOVE REAR SEAT CUSHION ASSEMBLY LH


    1. for Power Seat:

      Click here

    2. for Ottoman:

      Click here

  8. REMOVE REAR SEAT CUSHION ASSEMBLY RH


    1. for Power Seat:

      Click here

    2. for Ottoman:

      Click here

  9. REMOVE REAR SEAT CUSHION ASSEMBLY (for Fixed Seat Type)


    1. A01GXB4E01
      Text in Illustration
      *A w/ Seat Heater System

      Detach the 3 front hooks of the bench type rear seat cushion assembly from the vehicle body.

      Note

      Follow the instructions below carefully as the cushion frame deforms easily.

    2. Choose a hook to detach first. Place your hands near the hook. Then lift the bench type rear seat cushion assembly to detach the hook.

    3. Repeat the step above for the other hook.

    4. Detach the 2 rear hooks of the bench type rear seat cushion assembly from the bench type rear seatback assembly.

    5. w/ Seat Heater System:

      Disconnect the 2 connectors.

    6. Remove the bench type rear seat cushion assembly.

      Note

      Be careful not to damage the vehicle body.

  10. REMOVE REAR CENTER SEAT CUSHION ASSEMBLY


    1. for Power Seat:

      Click here

    2. for 5-Passenger with Ottoman:

      Click here

  11. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. A01GX2W

      Remove the bolt and disconnect the anchor part of the rear seat 3 point type belt assembly LH.

  12. DISCONNECT REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH

    Tech Tips

    Use the same procedures described for the LH side

  13. DISCONNECT REAR SEAT OUTER BELT ASSEMBLY CENTER

    A01GW56

    1. for Power Seat, 5-Passenger with Ottoman:

      Remove the nut and disconnect the anchor part of the rear seat outer belt assembly center.

    2. A01H1WD

      for Fixed Seat Type:

      Remove the nut and disconnect the anchor part of the rear seat outer belt assembly center.

  14. REMOVE REAR SEAT LOWER CONSOLE BOX COVER (for 4-Passenger with Ottoman)


    1. A01GYU2

      Using a screwdriver, detach the 4 claws, then detach the 2 hooks and remove the rear seat lower console box cover.

      Tech Tips

      Tape the screwdriver tip before use.

  15. REMOVE REAR SEAT CONSOLE BOX ASSEMBLY (for 4-Passenger with Ottoman)


    1. A01H0C9

      Using a screwdriver, detach the 4 clips and remove the rear seat console box front panel.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01H102

      Remove the 4 bolt and service plug cover.

    3. A01H12T

      Remove the 6 bolts, and move the rear seat console box assembly in the direction of the arrow shown in the illustration. Then detach the 2 clips, and remove it.

    4. A01H0EE

      Disconnect the connector.

  16. REMOVE REAR SEATBACK ASSEMBLY LH


    1. for Power Seat:

      Click here

    2. for Ottoman:

      Click here

  17. REMOVE REAR SEATBACK ASSEMBLY RH


    1. for Power Seat:

      Click here

    2. for Ottoman:

      Click here

  18. REMOVE REAR SEATBACK ASSEMBLY (for Fixed Seat Type)


    1. A01H1P1

      Remove the 2 bolts and nut to disconnect the 3 belt anchors of the rear seat 3 point type belt assembly LH, rear seat 3 point type belt assembly RH and rear center seat outer belt assembly.

    2. A01H0KUE04
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the 2 claws to open the 2 caps of the rear seat shoulder belt guide.

      Tech Tips


      • Tape the screwdriver tip before use.

      • Use the same procedure to open the 2 caps on the other side.

    3. Disconnect the rear seat outer belt from the rear seat shoulder belt guide.

      Tech Tips

      Use the same procedure to disconnect the rear seat outer belt on the other side.

    4. Lower the rear center armrest assembly.

    5. A01GWGA

      Lower the rear center seat headrest assembly.

    6. A01GZT1E04

      Detach the 2 clips. Then detach the hook by lowering the rear seat armrest hole board, and remove it.

    7. A01GZ6J

      w/ Seat Heater System:


      1. Remove the bolt and pull out the junction block.

      2. Disconnect the connector.

    8. A01GWRJE02

      Remove the 4 bolts and nut.

    9. Lift the bench type rear seatback assembly to detach the 2 hooks.

    10. Disconnect the rear center armrest assembly connector to remove the bench type rear seatback assembly.

      Note

      Be careful not to damage the vehicle body.

  19. REMOVE REAR SEAT CENTER ARMREST ASSEMBLY


    1. for Power Seat:

      Click here

    2. for 5-Passenger with Ottoman:

      Click here

  20. REMOVE REAR DOOR SCUFF PLATE LH


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  21. REMOVE REAR DOOR SCUFF PLATE RH


    1. for Standard Body:

      Click here

    2. for Long Body:

      Click here

  22. REMOVE REAR SEAT SIDE GARNISH LH

    A01GW72

    1. Detach the 6 claws and remove the rear seat side garnish LH.

  23. REMOVE REAR SEAT SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  24. REMOVE INNER ROOF SIDE GARNISH LH

    A01GW31E10
    Text in Illustration
    *1 Clip A

    1. Pull the inner roof side garnish LH away from the body to detach the 4 clips (do not detach clip A).

    2. Detach the 2 claws of the guide, and pull the inner roof side garnish LH in the direction of the arrow to remove it.

      Tech Tips

      Clip A remains attached to the body.

    3. Remove clip A from the vehicle body.

  25. REMOVE INNER ROOF SIDE GARNISH RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. REMOVE PACKAGE TRAY TRIM PANEL ASSEMBLY


    1. A01GWDN

      except 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 3 belt guides.

    2. for 4-Passenger with Ottoman:

      Using a moulding remover D, detach the 4 claws and remove the 2 belt guides.

    3. A01GY1H

      except 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel assembly. Then pass the 3 rear seat belt floor anchors through the package tray trim panel assembly.

    4. A01H1AU

      for 4-Passenger with Ottoman:

      Detach the 2 clips of the package tray trim panel assembly. Then pass the 2 rear seat belt floor anchors through the package tray trim panel assembly.

    5. Disconnect the solar sensor connector and remove the package tray trim panel.

  27. REMOVE ROOF SIDE NO. 2 AIR DUCT LH (w/ Rear Cooler)


    1. A01H1EA

      Remove the clip.

    2. Detach the 2 claws and remove the No. 2 roof side air duct LH.

  28. REMOVE ROOF SIDE NO. 2 AIR DUCT RH (w/ Rear Cooler)


    1. A01GXBK

      Remove the clip.

    2. Detach the 2 claws and remove the No. 2 roof side air duct RH.

  29. REMOVE NO. 4 AIR DUCT REAR (w/ Rear Cooler)


    1. A01GZBW

      Detach the 4 claws and remove the rear No. 4 air duct.

  30. REMOVE NO. 5 AIR DUCT REAR (w/ Rear Cooler)


    1. A01GXSD

      Detach the 6 claws and remove the rear No. 5 air duct.

  31. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY LH


    1. A01GXJK

      Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. w/ Tension Reducer System:

      Disconnect the tension reducer connector.

    3. A01H0NV

      Remove the bolt.

    4. Detach the claw and remove the rear seat 3 point type belt assembly LH.

  32. REMOVE REAR SEAT 3 POINT TYPE BELT ASSEMBLY RH


    1. A01H06K

      Using a screwdriver, pull out the locking button in the direction shown by the arrow in the illustration to release the lock, and disconnect the pretensioner connector as shown in the illustration.

      Tech Tips

      Tape the screwdriver tip before use.

    2. Detach the wire harness clamp.

    3. w/ Tension Reducer System:

      Disconnect the tension reducer connector.

    4. A01GX49

      Remove the bolt.

    5. Detach the claw and remove the rear seat 3 point type belt assembly RH.

  33. REMOVE REAR SEAT OUTER BELT ASSEMBLY CENTER

    A01GXZZ

    1. Remove the 2 bolts and rear seat outer belt assembly center.