DRIVER SIDE KNEE AIRBAG ASSEMBLY REMOVAL

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. PRECAUTION

    CAUTION:

    Be sure to read Precaution thoroughly before servicing Click here.

    Note

    After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  2. REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  3. REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  4. REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  5. REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape

      Detach the clip, fastening tape and remove the battery service hole cover LH.

  6. DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    CAUTION:

    Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  7. REMOVE INSTRUMENT PANEL FINISH PANEL END LH

    A01GX53

    1. Pull the front part of the instrument panel finish panel end LH to detach the 6 clips.

    2. Pull the instrument panel finish panel end LH to detach 3 clips and remove the instrument panel finish panel end LH.

  8. REMOVE INSTRUMENT SIDE PANEL LH

    A01H24EE01
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Using moulding remover D, detach the 6 clips and remove the instrument side panel LH.

  9. REMOVE INSTRUMENT PANEL ORNAMENT

    A01GW3QE01
    Text in Illustration
    *1 Protective Tape

    1. Apply protective tape as shown in the illustration.

    2. Using moulding remover B, detach the 4 clips and remove the instrument panel ornament.

    3. Disconnect the connector.

  10. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

    A01GYFZ

    1. Remove the 2 screws.

    2. Detach the 2 claws as shown in the illustration and remove the No. 1 instrument panel under cover sub-assembly.

    3. Detach the 2 claws and disconnect the DLC3.

    4. Disconnect each connector and detach each wire harness clamp.

  11. REMOVE NO. 1 INSTRUMENT PANEL SAFETY PAD SUB-ASSEMBLY


    1. A01GX9OE01
      Text in Illustration
      *1 Protective Tape

      Using a screwdriver, detach the claw and remove the switch base hole cover from the No. 1 instrument panel safety pad sub-assembly.

      Tech Tips

      Tape the screwdriver tip before use.

    2. A01H1X8

      Remove the bolt.

    3. Remove the screw <C>.

    4. Detach the 5 clips and claw and remove the No. 1 instrument panel safety pad sub-assembly.

    5. Disconnect each connector.

  12. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY

    CAUTION:

    When storing the driver side knee airbag assembly, keep the airbag deployment side facing upward.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01GXF4

      Remove the 4 bolts.

    4. Detach the clip and remove the driver side knee airbag assembly.

    5. Detach the claw to disconnect the hood lock control lever sub-assembly from the driver side knee airbag assembly.

    6. Using a screwdriver release the airbag connector lock.

    7. Disconnect the airbag connector.

      Note

      When disconnecting airbag connector, take care not to damage the airbag wire harness.