SPIRAL CABLE INSTALLATION

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.


  1. INSTALL STEERING SENSOR


    1. A01GZ13E05
      Text in Illustration
      *1 Pin

      Align the 2 pins of the spiral cable sub-assembly with the locations shown in the illustration and attach the 6 claws to install the spiral cable subassembly to the steering sensor.

  2. INSTALL SPIRAL CABLE SUB-ASSEMBLY WITH SENSOR

    Note


    • Do not replace the spiral cable sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Do not rotate the spiral cable sub-assembly with the auxiliary battery connected and the power switch on (IG).

    • Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. Check that the front wheels are facing straight ahead.

    4. Attach the 3 claws to install the spiral cable subassembly with sensor.

      Note

      When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

    5. A01H1UJ

      Connect the yellow airbag connector to the spiral cable sub-assembly with sensor.

    6. Connect the connectors to the spiral cable sub-assembly with sensor.

      Note

      When connecting airbag connector, take care not to damage the airbag wire harness.

  3. INSTALL STEERING COLUMN COVER


    1. w/o Driver Monitor Camera:

      Click here

    2. w/ Driver Monitor Camera:

      Click here

  4. PLASE FRONT WHEELS TO FACING STRAIGHT AHEAD

  5. ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable sub-assembly with sensor with the auxiliary battery connected and the power switch on (IG).


    1. Check that the power switch is off.

    2. Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

    3. A01H0OX

      Rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

      CAUTION:

      Do not turn the spiral cable sub-assembly using the airbag wire harness.

    4. A01GWVUE01
      Text in Illustration
      *A w/o Steering Heater
      *B w/ Steering Heater
      *a Alignment Mark

      Rotate the spiral cable sub-assembly clockwise approximately 2.5 turns to align the marks.

      CAUTION:

      Do not turn the spiral cable sub-assembly using the airbag wire harness.

      Tech Tips

      The spiral cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  6. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  7. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note


    • Make sure that the cable has been disconnected from the auxiliary battery terminal for at least 2 seconds before reconnecting the cable.

    • Connect the cable to the negative (-) auxiliary battery terminal with the front wheels facing straight ahead.

    • When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  8. ENABLE AUTOAWAY/RETURN FUNCTION


    1. Restore the autoaway/return function setting to the previous condition by changing the customize parameter Click here.

  9. INSPECT STEERING PAD


    1. Make sure that the horn sounds.

      Tech Tips

      If the horn does not sound, inspect the horn system Click here.

  10. CHECK SRS WARNING LIGHT

    Click here

  11. INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman

      Attach the battery service hole cover LH with the clip and fastening tape.

  12. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  13. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  14. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI