AIRBAG SYSTEM, Diagnostic DTC:B1880/68, B1881/68, B1882/68, B1883/68

DTC Code DTC Name
B1880/68 Short in Rear Seat Cushion Squib RH Circuit
B1881/68 Open in Rear Seat Cushion Squib RH Circuit
B1882/68 Short to GND in Rear Seat Cushion Squib RH Circuit
B1883/68 Short to B+ in Rear Seat Cushion Squib RH Circuit

DESCRIPTION

The rear seat cushion squib RH circuit consists of the center airbag sensor assembly and the rear seat cushion squib RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are recorded when a malfunction is detected in the rear seat cushion squib RH circuit.

Tech Tips

These DTCs are LHD only.

DTC Code Detection Condition Trouble Area
B1880/68

One of the following conditions is met:


  • The center airbag sensor assembly receives a line short circuit signal 5 times in the rear seat cushion squib RH circuit during the primary check.

  • Rear seat cushion squib RH malfunction

  • Center airbag sensor assembly malfunction

  • Floor wire

  • Rear seat wire RH

  • Rear seat cushion airbag assembly RH (Rear seat cushion squib RH)

  • Center airbag sensor assembly
B1881/68

One of the following conditions is met:


  • The center airbag sensor assembly receives an open circuit signal in the rear seat cushion squib RH circuit for 2 seconds.

  • Rear seat cushion squib RH malfunction

  • Center airbag sensor assembly malfunction

  • Floor wire

  • Rear seat wire RH

  • Rear seat cushion airbag assembly RH (Rear seat cushion squib RH)

  • Center airbag sensor assembly
B1882/68

One of the following conditions is met:


  • The center airbag sensor assembly receives a short circuit to ground signal in the rear seat cushion squib RH circuit for 0.5 seconds.

  • Rear seat cushion squib RH malfunction

  • Center airbag sensor assembly malfunction

  • Floor wire

  • Rear seat wire RH

  • Rear seat cushion airbag assembly RH (Rear seat cushion squib RH)

  • Center airbag sensor assembly
B1883/68

One of the following conditions is met:


  • The center airbag sensor assembly receives a short circuit to B+ signal in the rear seat cushion squib RH circuit for 0.5 seconds.

  • Rear seat cushion squib RH malfunction

  • Center airbag sensor assembly malfunction

  • Floor wire

  • Rear seat wire RH

  • Rear seat cushion airbag assembly RH (Rear seat cushion squib RH)

  • Center airbag sensor assembly

WIRING DIAGRAM

A01GYDSE13

INSPECTION PROCEDURE

Note


  • After turning the power switch OFF, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work Click here.

  • When disconnecting the cable from the negative (-) auxiliary battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected Click here.

Tech Tips


  • Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester Click here.

  • After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on various types of roads Click here.

PROCEDURE


  1. CHECK REAR SEAT CUSHION AIRBAG RH (REAR SEAT CUSHION SQUIB RH)

    A01GX75E03

    1. Turn the power switch OFF.

    2. Disconnect the negative (-) terminal cable from the auxiliary battery, and wait for at least 90 seconds.

    3. Disconnect the connectors from the rear seat cushion airbag RH.

    4. Connect the black wire side of SST (resistance: 2.1 Ω) to connector E.

      CAUTION:

      Never connect the tester to the rear seat cushion airbag RH (rear seat cushion squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    5. Connect the negative (-) terminal cable to the auxiliary battery, and wait for at least 2 seconds.

    6. Turn the power switch ON (IG), and wait for at least 60 seconds.

    7. Clear the DTCs Click here.

    8. Turn the power switch OFF.

    9. Turn the power switch ON (IG), and wait for at least 60 seconds.

    10. Check for DTCs Click here.

      OK
      DTC B1880, B1881, B1882 or B1883 is not output.

      Tech Tips

      Codes other than DTC B1880, B1881, B1882 and B1883 may be output at this time, but they are not related to this check.


    NG

    CHECK CONNECTOR Click here

    OK

    REPLACE REAR SEAT CUSHION ASSEMBLY RH Click here

  2. CHECK CONNECTOR


    1. Turn the power switch OFF.

    2. Disconnect the negative (-) terminal cable from the auxiliary battery, and wait for at least 90 seconds.

    3. Disconnect SST from connector E.

    4. Check that the floor wire and rear seat wire connectors (on the rear seat cushion airbag RH side) are not damaged.

      OK
      The lock button is not disengaged, or the claw of the lock is not damaged or deformed.

    NG

    REPLACE HARNESS AND CONNECTOR

    OK

  3. CHECK REAR SEAT CUSHION SQUIB RH CIRCUIT

    A01GY2DE07

    1. Disconnect the connectors from the center airbag sensor assembly.

    2. Connect the negative (-) terminal cable to the auxiliary battery, and wait for at least 2 seconds.

    3. Turn the power switch ON (IG).

    4. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      f18-1 (RCR+) - Body ground Power switch ON (IG) Below 1 V
      f18-2 (RCR-) - Body ground Power switch ON (IG) Below 1 V

    5. Turn the power switch OFF.

    6. Disconnect the negative (-) terminal cable from the auxiliary battery, and wait for at least 90 seconds.

    7. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      f18-1 (RCR+) - f18-2 (RCR-) Always Below 1 Ω

    8. Release the activation prevention mechanism built into connector B Click here.

    9. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      f18-1 (RCR+) - f18-2 (RCR-) Always 1 MΩ or higher
      f18-1 (RCR+) - Body ground Always 1 MΩ or higher
      f18-2 (RCR-) - Body ground Always 1 MΩ or higher

    NG

    CHECK REAR SEAT WIRE RH Click here

    OK

  4. CHECK CENTER AIRBAG SENSOR ASSEMBLY


    1. Connect the connectors to the rear seat airbag RH and the center airbag sensor assembly.

    2. Connect the negative (-) terminal cable to the auxiliary battery, and wait for at least 2 seconds.

    3. Turn the power switch ON (IG), and wait for at least 60 seconds.

    4. Clear the DTCs Click here.

    5. Turn the power switch OFF.

    6. Turn the power switch ON (IG), and wait for at least 60 seconds.

    7. Check for DTCs Click here.

      OK
      DTC B1880, B1881, B1882 or B1883 is not output.

      Tech Tips

      Codes other than DTC B1880, B1881, B1882 and B1883 may be output at this time, but they are not related to this check.


    NG

    REPLACE CENTER AIRBAG SENSOR ASSEMBLY Click here

    OK

    USE SIMULATION METHOD TO CHECK Click here

  5. CHECK REAR SEAT WIRE RH

    A01GZVSE03

    1. Restore the released activation prevention mechanism of connector B to its original condition.

    2. Disconnect the floor wire connector from the rear seat wire RH.

    3. Connect the negative (-) terminal cable to the auxiliary battery, and wait for at least 2 seconds.

    4. Turn the power switch ON (IG).

    5. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      Rf3-1 (RCR+) - Body ground Power switch ON (IG) Below 1 V
      Rf3-2 (RCR-) - Body ground Power switch ON (IG) Below 1 V

    6. Turn the power switch OFF.

    7. Disconnect the negative (-) terminal cable from the auxiliary battery, and wait for at least 90 seconds.

    8. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      Rf3-1 (RCR+) - Rf3-2 (RCR-) Always Below 1 Ω

    9. Release the activation prevention mechanism built into connector D Click here.

    10. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      Rf3-1 (RCR+) - Rf3-2 (RCR-) Always 1 MΩ or higher
      Rf3-1 (RCR+) - Body ground Always 1 MΩ or higher
      Rf3-2 (RCR-) - Body ground Always 1 MΩ or higher

    NG

    REPLACE REAR SEAT WIRE RH

    OK

    REPLACE FLOOR WIRE