AIR CONDITIONING SYSTEM Heater Water Pump Circuit

DESCRIPTION

The heater water pump assembly sends engine coolant to the heater core assembly while the engine is stopped to prevent heater effectiveness from becoming low. Directed by the air conditioning amplifier, the hybrid vehicle control ECU operates the water pump relay and drives the heater water pump assembly.

WIRING DIAGRAM

A01H0VCE02

INSPECTION PROCEDURE

PROCEDURE


  1. CHECK DTC (CAN COMMUNICATION SYSTEM)


    1. Use the intelligent tester to check if the CAN communication system is functioning normally.

      Result
      Result Proceed to
      CAN DTC is not output A
      CAN DTC is output (for LHD) B
      CAN DTC is output (for RHD) C

    B

    GO TO CAN COMMUNICATION SYSTEM Click here

    C

    GO TO CAN COMMUNICATION SYSTEM Click here

    A

  2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (WATER PUMP RELAY)


    1. Select the Active Test, using the intelligent tester to generate a control command, and then check that the heater water pump operates.

      Air Conditioner
      Tester Display Test Part Control Range Diagnostic Note
      Water Pump Water pump relay OFF or ON -
      Result
      Result Proceed to
      Heater water pump operates smoothly A
      Heater water pump does not operate smoothly B

    B

    INSPECT FUSE (A/C W/P, E/G R/M-IG1-1) Click here

    A

    PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE Click here

  3. INSPECT FUSE (A/C W/P, E/G R/M-IG1-1)


    1. Remove the A/C W/P and E/G R/M-IG1-1 fuses from the engine room No. 2 relay block.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A/C W/P fuse Always Below 1 Ω
      E/G R/M-IG1-1 fuse

    NG

    REPLACE FUSE

    OK

  4. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 JUNCTION BLOCK - BODY GROUND)

    A01GY5CE01

    1. Disconnect the 2G and 2F engine room No. 2 junction block connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      Tester Connection Condition Specified Condition
      2G-9 - Body ground Power switch ON (IG) 11 to 14 V
      2F-1 - Body ground Always

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. CHECK ENGINE ROOM NO. 2 JUNCTION BLOCK

    A01GZEOE01

    Tech Tips

    The A/C W/P relay is an inner circuit of the engine room No. 2 relay block.


    1. Remove the terminal cover from the engine room No. 2 junction block.

    2. Measure the voltage according to the value(s) in the table below for the A/C W/P relay terminal of the engine room No. 2 relay block.

      Standard voltage
      Tester Connection Condition Specified Condition
      2 - Body ground Power switch ON (IG) 11 to 14 V
      3 - Body ground Always 11 to 14 V

    NG

    REPLACE ENGINE ROOM NO. 2 JUNCTION BLOCK

    OK

  6. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 JUNCTION BLOCK - HYBRID VEHICLE CONTROL)

    A01GXKIE02

    1. Disconnect the 2G engine room No. 2 junction block connector.

    2. Disconnect the A77 hybrid vehicle control ECU connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A77-5 (WP) - 2G-10 Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (HEATER WATER PUMP ASSEMBLY - BODY GROUND)

    A01GZDCE02

    1. Disconnect the A82 heater water pump assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      A82-1 (-) - Body ground Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (ENGINE ROOM NO. 2 J/B - HEATER WATER PUMP ASSEMBLY)

    A01H10PE01

    1. Disconnect the 2C engine room No. 2 junction block connector.

    2. Disconnect the A82 heater water pump assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Condition Specified Condition
      2C-31 - A82-2 (+B) Always Below 1 Ω

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. INSPECT HEATER WATER PUMP ASSEMBLY

    A01GW8OE03

    1. Disconnect the A82 heater water pump assembly connector.

    2. Apply battery voltage to the terminals of the connector, and check the heater water pump operation.

      OK
      Measurement Condition Specified Condition

      Battery positive (+) - Terminal 2

      Battery negative (-) - Terminal 1

      		 Heater water pump operates smoothly

      Note

      Complete this inspection within 10 seconds if there is no water in the heater water pump assembly.


    NG

    REPLACE HEATER WATER PUMP ASSEMBLY Click here

    OK

  10. REPLACE AIR CONDITIONING AMPLIFIER


    1. Replace the air conditioning amplifier with a normal one and check that the condition returns to normal Click here.

      OK
      Same problem does not occur.

    NG

    REPLACE HYBRID VEHICLE CONTROL ECU Click here

    OK

    END (AIR CONDITIONING AMPLIFIER IS DEFECTIVE)