REAR BRAKE FLEXIBLE HOSE INSTALLATION

Tech Tips


  • Use the same procedures for the LH side and RH side.

  • The procedures listed below are for the LH side.

Note

While the battery is connected, even if the power switch is OFF, the brake control system activates when the brake pedal is depressed or the door courtesy switch turns on. Therefore during servicing of the brake system components, do not operate the brake pedal or open/close the doors while the battery is connected.


  1. INSTALL REAR BRAKE FLEXIBLE HOSE


    1. A01GZGI

      Connect the flexible hose with a new union bolt and a new gasket.

      Torque:
      39 N*m  { 400 kgf*cm, 29 ft.*lbf }

      Note

      Install the flexible hose lock securely in the lock hole in the disc brake caliper.

    2. Connect the brake tube to the flexible hose with a union nut wrench while holding the flexible hose with a wrench.

      Torque:
      15 N*m  { 155 kgf*cm, 11 ft.*lbf }

      Note


      • Do not bend or damage the brake tube.

      • Do not allow any foreign matter such as dirt and dust to enter the brake tube from the connecting points.

      • Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench Click here.

    3. Install the flexible hose with a new clip.

      Note

      Securely install the clip.

  2. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  3. INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman

      Attach the battery service hole cover LH with the clip and fastening tape.

  4. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  5. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  6. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI

  7. BLEED BRAKE LINE


    1. Bleed brake line.


      1. Remove the brake master cylinder reservoir filler cap assembly.

      2. Add brake fluid into the reservoir between MAX and MIN level on the brake fluid reservoir.

        Brake fluid
        SAE J1703 or FMVSS No. 116 DOT3

      3. Connect the intelligent tester to the DLC3 and turn the power switch on (IG).

      4. Turn the intelligent tester on and enter the following menus: Chassis / ABS/VSC/TRC / Utility / Air Bleeding.

      5. Select the "Usual air bleeding / All Line" and bleed brake line according to the intelligent tester display.

      6. After air bleeding, tighten each bleeder plug.

        Torque:
        for Front Brake (except 6-pot caliper)
        11 N*m  { 110 kgf*cm, 8 ft.*lbf }
        for Front Brake (6-pot caliper)
        19 N*m  { 194 kgf*cm, 14 ft.*lbf }
        for Rear Brake
        11 N*m  { 110 kgf*cm, 8 ft.*lbf }

    2. Clear the DTCs Click here.

    3. Turn the intelligent tester off and turn the power switch off.

    4. Inspect for brake fluid leaks.

    5. Adjust the brake fluid level in the reservoir Click here.

  8. INSTALL REAR WHEEL

    Torque:
    140 N*m  { 1428 kgf*cm, 103 ft.*lbf }

  9. CLEAR THE DTC

    Click here

  10. CHECK FOR DTC


    1. Check for DTC. If any DTC is output, perform the troubleshooting for that DTC Click here.