Click here

FRONT DOOR LOCK REMOVAL

Click here
Click here Click here
Tip:

  • Use the same procedure for the RH and LH sides.

  • The procedure listed below is for the LH side.

Click here
  1. Click here

    PRECAUTION

    Note:

    After turning the power switch off, waiting time may be required before disconnecting the cable from the auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the auxiliary battery terminal notice before proceeding with work (Click here).

  2. Click here

    REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

  3. Click here

    REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)

  4. Click here

    REMOVE DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Detach the 2 clips and remove the deck trim side board LH.

  5. Click here

    REMOVE BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02

      Detach the clip, fastening tape and remove the battery service hole cover LH.

      Table 1. Text in Illustration
      *A for Standard
      *B for Ottoman
      *1 Fastening Tape
  6. Click here

    DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  7. Click here

    REMOVE DOOR INSIDE HANDLE BEZEL


    1. A01GWOPE03

      Using a screwdriver, detach the 3 claws and remove the front door inside handle bezel plug LH.

      Tip:

      Tape the screwdriver tip before use.

      Table 2. Text in Illustration
      *1 Protective Tape
  8. Click here

    REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY LH


    1. A01GWMP

      Using a moulding remover D, detach the 2 clips.

    2. Disconnect the connector and remove the power window regulator master switch assembly with front door armrest base panel.

      Tip:

      Tape the screwdriver tip before use.

  9. Click here

    REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH


    1. A01GYVZ

      Remove the 3 screws.

    2. Detach the 13 clips and remove the front door trim board sub-assembly LH.

    3. Disconnect the connector.

    4. A01GWSZ

      Disconnect the 2 cables from the inside handle.

  10. Click here

    REMOVE FRONT DOOR TRIM COVER LH


    1. A01GYADE01

      Remove the cushion.

      Table 3. Text in Illustration
      *1 Cushion

    2. Using a clip remover, detach the 5 clips.

  11. Click here

    REMOVE FRONT DOOR SERVICE HOLE COVER LH


    1. A01GY51

      Remove the front door service hole cover LH.

      Tip:

      Remove the remaining tape on the door.

  12. Click here

    REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH


    1. Connect the front door ECU LH.

    2. Temporarily install the power window regulator master switch assembly with front door armrest base panel.

    3. Connect the cable to the negative (-) battery terminal.

    4. Remove the hole plug.

    5. A01GYAX

      Move the front window regulator sub-assembly LH so that the front door glass sub-assembly LH bolts can be seen.

    6. Disconnect the cable from the negative (-) battery terminal.

      Note:

      When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

    7. Remove the 2 bolts.

      Note:

      Be careful when removing the bolts as the glass may fall and become damaged.

    8. A01GW9L

      Remove the front door glass sub-assembly in the direction indicated by the arrows in the illustration.

      Tip:

      Remove the glass upward.

      Note:

      Be careful not to damage the glass.

    9. Remove the power window regulator master switch assembly with front door armrest base panel.

    10. Disconnect the front door ECU LH.

  13. Click here

    REMOVE FRONT DOOR FRAME SUB-ASSEMBLY REAR LOWER LH


    1. A01H0FD

      Remove the 2 bolts and front door rear lower frame sub-assembly LH.

  14. Click here

    REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH


    1. A01GYK4

      Remove the hole plug.

    2. Using a T30 "TORX" wrench, loosen the screw and remove the front door outside handle cover LH with the door lock key cylinder installed.

    3. Remove the cylinder from the front door outside handle cover LH.

  15. Click here

    REMOVE FRONT DOOR LOWER FRAME GARNISH PAD LH


    1. A01H1PB

      Remove the 2 bolts and front door lower frame garnish pad LH.

  16. Click here

    REMOVE FRONT DOOR LOCK ASSEMBLY LH


    1. A01GWOIE01

      Disconnect the 2 connectors.

    2. Using a T30 "TORX" wrench, remove 3 screws labeled A and the 2 screws labeled B.

    3. Remove the front door lock assembly LH.

      Note:

      Be careful when removing the bolts as the door lock may fall and become damaged.

      Tip:

      Remove the door lock through the service hole.

  17. Click here

    REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH


    1. A01H015E03

      Using a screwdriver, detach the claw.

      Tip:

      Tape the screwdriver tip before use.

      Table 4. Text in Illustration
      *1 Protective Tape
    2. A01GZTG

      Remove the front door lock remote control cable assembly LH.

  18. Click here

    REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH


    1. A01GZPPE05

      Using a screwdriver, detach the 3 claws.

      Tip:

      Tape the screwdriver tip before use.

      Table 5. Text in Illustration
      *1 Protective Tape
    2. A01GWPR

      Remove the front door inside locking cable assembly LH.