REAR UPPER ARM REMOVAL

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.


  1. REMOVE REAR WHEEL

  2. REMOVE REAR DISC BRAKE CALIPER ASSEMBLY LH


    1. A01GY2Z

      Remove the 2 bolts and disconnect the rear disc brake caliper assembly.

      Note


      • Hang the caliper with wire or equivalent.

      • Do not damage the brake hose.

  3. REMOVE REAR STABILIZER LINK ASSEMBLY LH

    A01H0EB

    1. Remove the nut and disconnect the stabilizer link from the stabilizer bar.

    2. A01GZFR

      Remove the bolt, nut and stabilizer link from the rear No. 2 suspension arm.

  4. DISCONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH

    A01H0LT

    1. Remove the nut and disconnect the pneumatic cylinder from the axle side.

  5. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    A01GYOME01

    1. Using a plastic-faced hammer or equivalent, strike the part labeled A from the rear of the vehicle to maintain the clearance at the slide pin area.

      Note

      Be careful not to damage the arm.

    2. A01GX4B

      Remove the nut, washer, bolt and No. 2 suspension arm from the axle carrier.

    3. A01GZN7

      Remove the nut, No. 2 suspension toe adjust plate, rear suspension attachment and No. 2 suspension arm from the suspension member.

  6. DISCONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. Remove the nut from the rear No. 1 suspension arm.

    2. Install 2 spacers (SST spacer B) onto the rear No. 1 suspension arm so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

      SST
      09960-20010   ( 09961-02060 )

      Note


      • Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.

      • As SST may become damaged, make sure the space between the arm and spacers is not less than 1 mm (0.0394 in.).

      A01GY9ME02

    3. Using SST, disconnect the rear No. 1 suspension arm from the axle carrier.

      SST
      09960-20010   ( 09961-02010 )

      Note


      • Apply molybdenum grease to the threads and end of the SST bolt.

      • Do not damage the ball joint dust cover.

      • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

  7. DISCONNECT TOE CONTROL LINK SUB-ASSEMBLY LH


    1. Remove the nut on the rear axle carrier side.

    2. Install 2 spacers (SST spacer B) onto the toe control link so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

      SST
      09960-20010   ( 09961-02060 )

      Note


      • Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.

      • As SST may become damaged, make sure the space between the arm and spacers is not less than 1 mm (0.0394 in.).

      A01H0M2E02

    3. Using SST, disconnect the toe control link from the axle carrier.

      SST
      09960-20010   ( 09961-02010 )

      Note


      • Apply molybdenum grease to the threads and end of the SST bolt.

      • Do not damage the ball joint dust cover.

      • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

  8. REMOVE REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH


    1. Remove the nut on the rear axle carrier side.

    2. Install 2 spacers (SST spacer A) onto the rear upper No. 1 control arm so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

      A01GXCYE02
      SST
      09960-20010   ( 09961-02050 )

      Note


      • Make sure to install the spacers (SST spacer A) as the axle carrier spacer may shift.

      • As SST may become damaged, make sure the space between the arm and spacers is not less than 1 mm (0.0394 in.).

    3. Using SST, disconnect the rear upper No. 1 control arm from the axle carrier.

      SST
      09960-20010   ( 09961-02010 )

      Note


      • Apply molybdenum grease to the bolt threads and end of the SST bolt.

      • Do not damage the dust cover.

      • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

    4. A01H0TO

      Remove the nut, washer, bolt and control arm from the rear suspension member.

  9. REMOVE REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH


    1. Remove the nut on the rear axle carrier side.

    2. Install 2 spacers (SST spacer A) onto the rear upper No. 2 control arm so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

      A01H16KE02
      SST
      09960-20010   ( 09961-02050 )

      Note


      • Make sure to install the spacers (SST spacer A) as the axle carrier spacer may shift.

      • As SST may become damaged, make sure the space between the arm and spacers is not less than 1 mm (0.0394 in.).

    3. Using SST, disconnect the rear upper No. 2 control arm from the axle carrier.

      SST
      09960-20010   ( 09961-02010 )

      Note


      • Apply molybdenum grease to the bolt threads and end of the SST bolt.

      • Do not damage the dust cover.

      • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

    4. A01H0V9

      Remove the nut, washer, bolt and rear control arm from the rear suspension member.