TIRE PRESSURE WARNING SYSTEM, Diagnostic DTC:C2126/26

DTC Code DTC Name
C2126/26 Transmitter ID not Received in Main Mode

DESCRIPTION

After all IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and receiver and the tire pressure warning light blinks for 1 minute and then illuminates.

When the tire pressure warning ECU and receiver successfully receives radio waves from all the transmitters whose IDs are stored in the ECU, DTC C2126/26 is cleared and the tire pressure warning light goes off.

DTC No. DTC Detection Condition Trouble Area
C2126/26 After ID registration is completed, ECU does not receive radio waves from transmitters whose IDs are stored in ECU.

  • ID registration failure

  • Tire pressure warning valve and transmitter

  • Tire pressure warning antenna (for Roof Side)

  • Tire pressure warning antenna (for Front Side)

  • Harness or connector

  • Tire pressure warning ECU and receiver

Note

w/ ID Switching Function:

(Main) is displayed on the DTC screen for the DTCs even when the 2nd set of tires is selected.

Tech Tips

The purpose of this DTC is to help prevent delivering a vehicle that has incorrectly registered IDs. After all IDs are registered, DTC C2126/26 is detected and the tire pressure warning light blinks for 1 minute and then illuminates. If the tire pressure warning light does not turn off after a little while, IDs may be incorrectly registered.

WIRING DIAGRAM

A01GZKME05

INSPECTION PROCEDURE

Note


  • When replacing the tire pressure warning ECU and receiver, read the transmitter IDs stored in the old ECU using the GTS and write them down before removal.

  • It is necessary to perform initialization Click here after registration Click here of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU and/or one of the valve and transmitters has been replaced.

PROCEDURE


  1. CHECK TEST MODE DTC (C2195/95)


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

    6. Perform the test mode inspection Click here.

      Result
      Result Proceed to
      DTC C2195/95 is cleared A
      DTC C2195/95 is not cleared B

    B

    GO TO DTC C2195/95 Click here

    A

  2. IDENTIFY TRANSMITTER NOT RECEIVED


    1. Set the tire pressure to the specified value Click here.

    2. Turn the power switch off.

    3. Connect the GTS to the DLC3.

    4. Turn the power switch on (IG).

    5. Turn the GTS on.

    6. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

    7. Check the values by referring to the table below.

      Tire Pressure Monitor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ID 1 Tire Inflation Pressure

      ID1 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*1
      ID 2 Tire Inflation Pressure

      ID2 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*1
      ID 3 Tire Inflation Pressure

      ID3 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*1
      ID 4 Tire Inflation Pressure

      ID4 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*1
      ID 5 Tire Inflation Pressure

      ID5 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure*2 If N/A is displayed, data has not been received.*1, *2

      Tech Tips


      • *1: It may take a few minutes until the values are displayed.

      • *2: w/ Spare Tire

    8. Rapidly reduce the tire pressure for each wheel at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds.

    9. Check the Data List.

      Note


      • It may take a few minutes to display the updated tire pressure data.

      • When the "ID Tire Inflation Pressure" data has not changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.

      • Record the "ID Tire Inflation Pressure" data transmitter ID that corresponds to each tire.

    10. After confirming that the "ID Tire Inflation Pressure" data for one tire has changed, repeat this procedure one by one. Identify the transmitter not received.

      Result
      Condition Proceed to
      One or more of transmitters abnormal A
      All normal B

    B

    PERFORM INITIALIZATION Click here

    A

  3. CHECK TRANSMITTER ID


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

    6. Check the values by referring to the table below.

      Tire Pressure Monitor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Registered ID 1 code

      Registered ID1 code/

      min.: 0, max.: FFFFFFF*1

      		 ID No. registered for transmitter ID1 displayed -
      Registered ID 2 code

      Registered ID2 code/

      min.: 0, max.: FFFFFFF*1

      		 ID No. registered for transmitter ID2 displayed -
      Registered ID 3 code

      Registered ID3 code/

      min.: 0, max.: FFFFFFF*1

      		 ID No. registered for transmitter ID3 displayed -
      Registered ID 4 code

      Registered ID4 code/

      min.: 0, max.: FFFFFFF*1

      		 ID No. registered for transmitter ID4 displayed -
      Registered ID 5 code

      Registered ID5 code/

      min.: 0, max.: FFFFFFF*1

      		 ID No. registered for transmitter ID5 displayed*2 -

      Tech Tips


      • *1: Displayed only when the ID No. is not registered.

      • *2: w/ Spare Tire

    7. Check the ID number on the identified transmitter by removing it from the tire and wheel.

      A01GXJVE01
      Text in Illustration
      *1 Tire Pressure Warning Valve and Transmitter *2 Transmitter ID (7-digit number)

    8. Confirm that the ID number on the transmitter and recorded transmitter ID match.

      Result
      Result Proceed to
      Match A
      Do not match B

    B

    REGISTRATION OF TRANSMITTER ID Click here

    A

  4. REPLACE TIRE PRESSURE WARNING VALVE AND TRANSMITTER


    1. Replace the tire pressure warning valve and transmitter Click here.


    NEXT

  5. REGISTRATION OF TRANSMITTER ID


    1. Perform registration Click here.


    NEXT

  6. PERFORM INITIALIZATION


    1. Perform initialization Click here.


    NEXT

  7. CONFIRM TIRE INFLATION PRESSURE (DATA LIST)


    1. Turn the power switch off.

    2. Connect the GTS to the DLC3.

    3. Turn the power switch on (IG).

    4. Turn the GTS on.

    5. Enter the following menus: Chassis / Tire Pressure Monitor / Data List.

    6. Check the values by referring to the table below.

      Tire Pressure Monitor
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ID 1 Tire Inflation Pressure

      ID1 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*1
      ID 2 Tire Inflation Pressure

      ID2 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*1
      ID 3 Tire Inflation Pressure

      ID3 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*1
      ID 4 Tire Inflation Pressure

      ID4 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure If N/A is displayed, data has not been received.*1
      ID 5 Tire Inflation Pressure

      ID5 tire inflation pressure/

      min.: Absolute pressure / 0 kPa (0 kgf/cm2, 0 psi), Relative pressure / 0 kPa (0 kgf/cm2, 0 psi)

      max.: Absolute pressure / 488.72 kPa (4.9 kgf/cm2, 70 psi), Relative pressure / 388.72 kPa (3.9 kgf/cm2, 56 psi)

      		 Actual tire inflation pressure*2 If N/A is displayed, data has not been received.*1, *2

      Tech Tips


      • *1: It may take a few minutes until the values are displayed.

      • *2: w/ Spare Tire

      • When no "ID Tire Inflation Pressure" data has changed, reset the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then rapidly release the tire pressure and recheck the data.

        Result
        Result Proceed to
        Tire pressure values are not displayed. A
        All tire pressure readings are equal to specified values. B

    B

    END

    A

    REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER Click here