REAR AXLE HUB REMOVAL

Tech Tips


  • Use the same procedures for the RH side and LH side.

  • The procedures listed below are for the LH side.


  1. REMOVE REAR WHEEL

  2. REMOVE LOAD SENSING VALVE SENSOR BRACKET


    1. A01GWMD

      Remove the bolt and load sensing valve sensor bracket from the toe control link sub-assembly.

  3. DISCONNECT REAR STABILIZER LINK ASSEMBLY LH


    1. A01GZFR

      Remove the bolt and nut, and then disconnect the rear stabilizer link assembly LH from the rear No. 2 suspension arm assembly LH.

  4. REMOVE REAR AXLE SHAFT NUT LH


    1. A01GZK4E01

      Using SST and a hammer, release the staked part of the rear axle shaft nut.

      SST
      09930-00010

      Note

      Release the staked part of the nut completely, otherwise the screw of the drive shaft may be damaged.

    2. While applying the brakes, remove the rear axle shaft nut.

  5. DISCONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH


    1. A01GY2Z

      Remove the 2 bolts and disconnect the rear disc brake caliper assembly.

      Note


      • Hang the caliper with wire or equivalent.

      • Do not damage the brake hose.

  6. DISCONNECT REAR SPEED SENSOR LH


    1. for RH:


      1. A01H07E

        Disconnect the sensor connector from the vehicle side connector.

    2. for LH:


      1. A01GY4Z

        Disconnect the sensor connector from the vehicle side connector.

    3. A01H16I

      Disconnect the grommet of the speed sensor wire from the hole of the wheel house.

    4. A01H0YI

      Disconnect the rear height control sensor connector.

    5. Remove the 2 nuts and 2 sensor clamps.

    6. A01H0TS

      Disconnect the pad wear indicator connector.

    7. Remove the bolt and sensor clamp.

    8. Disconnect the rear speed sensor connector.

      Note


      • Be careful not to damage the speed sensor.

      • Prevent foreign matter from adhering to the speed sensor.

  7. REMOVE PARKING BRAKE ASSEMBLY

    Click here

  8. DISCONNECT PNEUMATIC CYLINDER WITH REAR SHOCK ABSORBER ASSEMBLY LH

    A01H0LT

    1. Remove the nut and disconnect the pneumatic cylinder from the axle side.

  9. REMOVE REAR NO. 2 SUSPENSION ARM ASSEMBLY LH


    1. A01GYOME01

      Using a plastic-faced hammer or equivalent, strike the part labeled A from the rear of the vehicle to maintain the clearance at the slide pin area.

      Note

      Be careful not to damage the arm.

    2. A01GX4B

      Remove the bolt and nut, and then disconnect the rear No. 2 suspension arm assembly LH from the rear axle carrier.

    3. A01GZN7

      Remove the nut, rear suspension attachment sub-assembly, and rear No. 2 suspension toe adjust plate. Then remove the rear No. 2 suspension arm assembly.

  10. DISCONNECT REAR NO. 1 SUSPENSION ARM ASSEMBLY LH


    1. Remove the nut from the rear No. 1 suspension arm.

    2. Install 2 spacers (SST spacer B) onto the rear No. 1 suspension arm so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

      SST
      09960-20010   ( 09961-02060 )

      Note


      • Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.

      • As SST may become damaged, make sure the space between the arm and spacers is not less than 1 mm (0.0394 in.).

      A01GY9ME02

    3. Using SST, disconnect the rear No. 1 suspension arm from the axle carrier.

      SST
      09960-20010   ( 09961-02010 )

      Note


      • Apply molybdenum grease to the threads and end of the SST bolt.

      • Do not damage the ball joint dust cover.

      • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

  11. DISCONNECT TOE CONTROL LINK SUB-ASSEMBLY LH


    1. Remove the nut on the rear axle carrier side.

    2. Install 2 spacers (SST spacer B) onto the toe control link so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

      SST
      09960-20010   ( 09961-02060 )

      Note


      • Make sure to install the spacers (SST spacer B) as the steering knuckle spacer may shift.

      • As SST may become damaged, make sure the space between the arm and spacers is not less than 1 mm (0.0394 in.).

      A01H0M2E02

    3. Using SST, disconnect the toe control link from the axle carrier.

      SST
      09960-20010   ( 09961-02010 )

      Note


      • Apply molybdenum grease to the threads and end of the SST bolt.

      • Do not damage the ball joint dust cover.

      • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

  12. DISCONNECT REAR UPPER NO. 1 CONTROL ARM ASSEMBLY LH


    1. Remove the nut on the rear axle carrier side.

    2. Install 2 spacers (SST spacer A) onto the rear upper No. 1 control arm so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

      SST
      09960-20010   ( 09961-02050 )

      Note


      • Make sure to install the spacers (SST spacer A) as the steering knuckle spacer may shift.

      • As SST may become damaged, make sure the space between the arm and spacers is not less than 1 mm (0.0394 in.).

      A01GXCYE02

    3. Using SST, disconnect the upper No. 1 control arm from the axle carrier.

      SST
      09960-20010   ( 09961-02010 )

      Note


      • Apply molybdenum grease to the threads and end of the SST bolt.

      • Do not damage the ball joint dust cover.

      • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

  13. DISCONNECT REAR UPPER NO. 2 CONTROL ARM ASSEMBLY LH


    1. Remove the nut on the rear axle carrier side.

    2. Install 2 spacers (SST spacer A) onto the rear upper No. 2 control arm so that there is a space of approximately 1 mm (0.0394 in.) between the arm and spacers.

      SST
      09960-20010   ( 09961-02050 )

      Note


      • Make sure to install the spacers (SST spacer A) as the steering knuckle spacer may shift.

      • As SST may become damaged, make sure the space between the arm and spacers is not less than 1 mm (0.0394 in.).

      A01H16KE02

    3. Using SST, disconnect the upper No. 2 control arm from the axle carrier.

      SST
      09960-20010   ( 09961-02010 )

      Note


      • Apply molybdenum grease to the threads and end of the SST bolt.

      • Do not damage the ball joint dust cover.

      • As the dust cover may be damaged, adjust SST with the center nut so that the body and claw are parallel.

      • Make sure to tie the string of SST to the vehicle to prevent SST from dropping.

  14. REMOVE REAR AXLE ASSEMBLY LH


    1. Using a plastic-faced hammer, separate the drive shaft from the rear axle carrier sub-assembly.

    2. Remove the rear axle assembly.

      Note


      • Be careful not to damage the boots.

      • Use a wire or equivalent to keep the rear drive shaft assembly from hanging down.

  15. REMOVE REAR NO. 1 WHEEL BEARING DUST DEFLECTOR LH


    1. A01H01W

      Using a screwdriver, remove the bearing dust deflector from the rear axle carrier.

      Note

      Be careful not to dent or damage the axle carrier, as it is made of aluminum.

  16. REMOVE REAR AXLE HUB AND BEARING ASSEMBLY LH


    1. Hold the axle hub and bearing in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. A01GY20

      Remove the 4 bolts and axle hub and bearing from the rear axle carrier.

    3. A01GZHJ

      Remove the 2 nuts, parking brake anchor block, parking brake cable support bracket, and parking brake plate from the rear axle carrier.