DIFFERENTIAL MOUNT CUSHION INSTALLATION


  1. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION


    1. Pass SST bolts through the area shown in the illustration, and install the No. 1 mount cushion.

      SST
      09570-24011
      A01GWXFE01

      Note


      • Make sure the mount cushion installation angle misalignment is not over -3 to 3°

      • Make sure the mount cushion is not at an angle by first temporarily installing the mount cushion to the member before installing SST.

      • Before using SST bolts, apply hypoid gear oil to their threads.

      • Be sure to combine SST properly.

      • Confirm that SST contacts the entire seat surface of the mount cushion.

      • Do not install SST bolts at an angle.

      • Make sure SST bolts are tightened equally.

  2. INSTALL REAR NO. 2 DIFFERENTIAL MOUNT CUSHION


    1. Pass SST bolt through the area shown in the illustration, and install the No. 2 mount cushion.

      SST
      09570-24011
      A01H1W2E01

      Note


      • Make sure the mount cushion installation angle misalignment is not over -3 to 3°.

      • Make sure the mount cushion is not at an angle by first temporarily installing the mount cushion to the member before installing SST.

      • Before using SST bolt, apply hypoid gear oil to their threads.

      • Be sure to combine SST properly.

      • Confirm that SST contacts the entire seat surface of the mount cushion.

      • Do not install SST bolts at an angle.

  3. INSTALL REAR SUSPENSION MEMBER DAMPER


    1. A01GZ3U

      Install the rear suspension member damper with the 3 bolts.

      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

  4. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY

    Click here

  5. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY WITH DRIVE SHAFT


    1. Place the rear differential carrier assembly (with drive shaft) on a transmission jack.

      CAUTION:


      • As the rear differential carrier assembly (with drive shaft) is very heavy, securely support it with the transmission jack.

      • Perform this procedure with several people supporting the rear differential carrier assembly (with drive shaft) so that it does not tilt or fall.

    2. Slowly raise the transmission jack so that the rear differential carrier (with drive shaft) is at its installation position.

      Note

      When installing the rear differential carrier assembly (with drive shaft), do not damage the installation surface.

    3. A01GZ1DE01

      Temporarily install the rear differential mount stopper upper and lower with 2 new bolts (B).

      SST
      09961-00950

    4. Temporarily install 2 new bolts (A).

    5. Temporarily install a new bolt (C).

    6. Using SST and a 12 mm socket hexagon wrench, tighten the 2 bolts (A).

      Torque:
      without SST
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }
      with SST
      75 N*m  { 764 kgf*cm, 55 ft.*lbf }

      Note


      • Use a torque wrench with a fulcrum length of 400 mm (15.7 in.)

      • The torque value for use with SST is effective when SST is parallel to the torque wrench.

      • Tighten the bolts so that they do not interfere with the bolt holes of the mount cushions.

    7. Using SST and a 12 mm socket hexagon wrench, tighten the bolt (C).

      Torque:
      without SST
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }
      with SST
      75 N*m  { 764 kgf*cm, 55 ft.*lbf }

      Note


      • Use a torque wrench with a fulcrum length of 400 mm (15.7 in.)

      • The torque value for use with SST is effective when SST is parallel to the torque wrench.

      • Tighten the bolts so that they do not interfere with the bolt holes of the mount cushions.

    8. Tighten the 2 bolts (B).

      Torque:
      105 N*m  { 1071 kgf*cm, 77 ft.*lbf }

      Note

      Make sure that the rear differential mount stopper upper and lower are not shifted or tilted.

  6. INSTALL REAR AXLE ASSEMBLY

    Click here