OIL PUMP MOTOR CONTROLLER REMOVAL

REMOVE LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)
REMOVE DECK BOARD ASSEMBLY (w/o Spare Tire)
REMOVE DECK TRIM SIDE BOARD LH (w/ Spare Tire)
1. Detach the 2 clips and remove the deck trim side board LH.

REMOVE BATTERY SERVICE HOLE COVER LH

Text in Illustration
*A	for Standard
*B	for Ottoman
*1	Fastening Tape

Detach the clip, fastening tape and remove the battery service hole cover LH.

PRECAUTION

Note

After turning the power switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work Click here
DISCONNECT CABLE FROM AUXILIARY BATTERY NEGATIVE TERMINAL

Note

When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here
REMOVE V-BANK COVER SUB-ASSEMBLY
1. While using both hands, lift the rear side of the V-bank cover sub-assembly upwards to detach the 4 clips labeled B. Slide the V-bank cover sub-assembly towards the front of the vehicle to detach the 2 clips labeled A, and remove the V-bank cover sub-assembly.
  
  Note
  
  The V-bank cover sub-assembly may be damaged if its front and rear are lifted at the same time.
REMOVE AIR CLEANER INLET COVER SUB-ASSEMBLY
1. Remove the 5 clips labeled A.
2. Lift up the air cleaner inlet cover sub-assembly to detach the 4 clips labeled B, and remove the air cleaner inlet cover sub-assembly.
REMOVE NO. 1 AIR CLEANER INLET
1. Remove the 2 bolts.
2. Hold the No. 1 air cleaner inlet by the protrusions labeled A and B, and detach the connections.
3. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion labeled C.
4. Hold the No. 1 air cleaner inlet by the protrusions labeled D and E, and detach the connections.
5. Rotate the No. 1 air cleaner inlet as shown in the illustration to detach the protrusion labeled F.
REMOVE ENGINE ROOM SIDE COVER RH
1. for LHD:
  
  Remove the 5 clips and engine room side cover RH.
  
  Note
  
  Remove the clip labeled A by turning it to prevent the engine room side cover RH and bracket from being damaged.
  
  Tech Tips
  
  The clip labeled A cannot be removed from the engine room side cover RH.
2. for RHD:
  
  Remove the 5 clips and engine room side cover RH.
REMOVE OIL PUMP MOTOR CONTROLLER
CAUTION:

Be sure to perform the procedure as described below. Do not turn the power switch on (READY) before reconnecting the cable to the negative battery terminal.
1. Release the lock on the connector.
2. Release the lock lever on the connector as shown in the illustration. Disconnect the connector from the oil pump motor controller.
  
  Note
  
  When disconnecting the connector, do not apply excessive force to the wire harness.
3. Disconnect the connector from the oil pump motor controller.
4. Pull the lever to release the lock on the connector.
5. Release the lock lever on the connector as shown in the illustration. Disconnect the connector from the oil pump motor controller.
  
  Note
  
  When disconnecting the connector, do not apply excessive force to the wire harness.
6. Remove the 2 bolts and separate the oil pump motor controller with bracket from the vehicle.
  Note
  
  Do not drop the oil pump motor controller.
  
  When separating the oil pump motor controller, do not apply excessive force to the wire harness clamp located on the bracket.
7. Disconnect the clamp.
  
  Note
  
  When disconnecting the clamp, do not apply excessive force to the wire harness.
8. Remove the 3 bolts and oil pump motor controller.