SHIFT LEVER POSITION SENSOR INSTALLATION


  1. INSTALL PARK/NEUTRAL POSITION SWITCH

    Tech Tips

    Make sure that the manual valve lever shaft has not been rotated prior to installing the park/neutral position switch as the detent spring may become detached from the manual valve lever shaft.


    1. Install the park/neutral position switch to the hybrid vehicle transmission assembly.

    2. A01GWUI

      Temporarily install the 2 bolts.

      Tech Tips

      Fully tighten the bolts with the neutral alignment mark line aligned with the groove. [*1]

    3. A01H0J6E01

      Install a new lock washer and the nut.

      Torque:
      6.9 N*m  { 70 kgf*cm, 61 in.*lbf }
    4. A01H0N3

      Temporarily install the control shaft lever.

      Tech Tips

      Bend the tabs of the lock washer before fully tightening the nut. [*2]

    5. A01GWVVE01

      Turn the control shaft lever counterclockwise until it stops. Next, turn the control shaft lever clockwise 2 notches to set it to the N position.

    6. A01H0N3

      Remove the transmission control shaft lever.

    7. A01GZDQE03

      Align the neutral alignment mark line with the switch groove, and tighten the 2 adjusting bolts. [*1]

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }
    8. A01GYQV

      Using a screwdriver, bend the tabs of the lock washer.

      Note

      Make sure that the nut is held firmly.

    9. A01H0N3

      Install the transmission control shaft lever with the nut. [*2]

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }
    10. A01GXDL

      Connect the park/neutral position switch connector.

  2. INSTALL FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY


    1. A01GYMY

      Move the shift lever to the N position and tighten the nut while lightly pushing the lever toward the R position.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

      Note

      Do not push the shift lever too hard.

  3. INSTALL OIL COOLER TUBE


    1. A01H0WVE01

      Install the oil cooler tube with the 3 bolts in the order shown in the illustration.

      Torque:
      12 N*m  { 122 kgf*cm, 9 ft.*lbf }

  4. CONNECT CABLE TO AUXILIARY BATTERY NEGATIVE TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected Click here.

  5. INSPECT SHIFT LEVER POSITION


    1. A01GYMY

      Remove the nut, and disconnect the floor shift gear shifting rod sub-assembly.

    2. A01GWVVE01

      Turn the control shaft lever counterclockwise until it stops. Next, turn the control shaft lever clockwise 2 notches to set it to the N position.

    3. Move the shift lever to the N position and tighten the nut while lightly pushing the shift lever toward the R position.

      Torque:
      13 N*m  { 130 kgf*cm, 9 ft.*lbf }

      Note

      Do not push the shift lever too hard.

    4. Check that the shift lever moves smoothly and the shift lever and gear operate correctly.

  6. INSPECT PARK/NEUTRAL POSITION SWITCH POSITION


    1. Apply the parking brake.

    2. Chock the wheels to secure the vehicle.

    3. Turn the power switch on (READY).

    4. Move the shift lever to the D position and release the brake pedal.

      Note

      Be sure to apply the parking brake and chock the wheels to secure the vehicle.

    5. Slowly move the shift lever to the N position and measure moving distance (A) of the shift lever from the original point to the gear activation point.

      Note

      Be sure to move the shift lever slowly.

    6. Move the shift lever to the R position and release the brake pedal.

      Note

      Be sure to apply the parking brake and chock the wheels to secure the vehicle.

    7. Slowly move the shift lever to the N position and measure moving distance (B) of the shift lever from the original point to the gear activation point.

      Note

      Be sure to move the shift lever slowly.

    8. Check that moving distances (A) and (B) shown in the illustration are almost the same.

      A01H0YBE01

      Tech Tips


      • If moving distances (A) and (B) are almost the same, adjustment of the shift lever position is not necessary.

      • If moving distance (A) is shorter than (B), perform adjustment of the shift lever position [*1].

      • If moving distance (B) is shorter than (A), perform adjustment of the shift lever position [*2].

  7. ADJUST PARK/NEUTRAL POSITION SWITCH POSITION


    1. If moving distance (A) is shorter than (B) [*1]:

      A01H1KWE01

      Tech Tips

      When the shift lever is moved from the R to N position, the moving distance of the shift lever from the original point to the gear activation point becomes longer.


      1. Move the shift lever to the N position.

      2. A01GZH2

        Loosen the 2 bolts.

      3. Slightly turn the park/neutral position switch clockwise.

      4. A01GZH2

        Tighten the park/neutral position switch with the 2 bolts.

        Torque:
        5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      5. Recheck the shift lever position.

    2. If moving distance (B) is shorter than (A) [*2]:

      A01GYWCE01

      Tech Tips

      If the shift lever is moved from the D to N position, the moving distance of the shift lever from the original point to the gear activation point becomes longer.


      1. Move the shift lever to the N position.

      2. A01GZH2

        Loosen the 2 bolts.

      3. Slightly turn the park/neutral position switch counterclockwise.

      4. A01GZH2

        Tighten the park/neutral position switch with the 2 bolts.

        Torque:
        5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

      5. Recheck the shift lever position sensor position.

  8. INSPECT SHIFT LEVER OPERATION


    1. While moving the shift lever from the N position to each position, check that the lever moves smoothly and that the shift position indicator comes on properly according to the shift lever position.

    2. Turn the power switch on (READY) and check the following:


      1. When the shift lever is moved to the D position, the vehicle moves forward.

      2. When the shift lever is moved to the R position, the buzzer sounds and the vehicle moves in reverse.

        Note

        The vehicle should not move when the shift position indicator is off.

  9. INSTALL FRONT LOWER SUSPENSION MEMBER PROTECTOR


    1. A01H26PE01

      Install the front lower suspension member protector with the 9 bolts.

      Torque:
      for bolt A
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }
      except bolt A
      58 N*m  { 593 kgf*cm, 43 ft.*lbf }

  10. INSTALL NO. 1 ENGINE UNDER COVER


    1. Install the No. 1 engine under cover with the 13 screws and 7 clips.

  11. INSTALL FRONT WHEEL OPENING EXTENSION PAD RH

    Tech Tips

    Use the same procedure described for the LH side.

  12. INSTALL FRONT WHEEL OPENING EXTENSION PAD LH


    1. Install the front wheel opening extension pad LH with the 5 screws.

  13. INSTALL NO. 2 ENGINE UNDER COVER


    1. Install the No. 2 engine under cover with the 4 screws and 2 clips.

  14. INSTALL FRONT CENTER FLOOR COVER (w/ Cover)


    1. Install the front center floor cover with the 3 screws, 2 bolts and clip.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

  15. INSTALL BATTERY SERVICE HOLE COVER LH


    1. A01GZIME02
      Text in Illustration
      *A for Standard
      *B for Ottoman

      Attach the battery service hole cover LH with the clip and fastening tape.

  16. INSTALL DECK TRIM SIDE BOARD LH (w/o Spare Tire)


    1. A01GXQQ

      Attach the 2 clips to install the deck trim side board LH.

  17. INSTALL DECK BOARD ASSEMBLY (w/o Spare Tire)

    A01GZ3P

  18. INSTALL LUGGAGE COMPARTMENT MAT SUB-ASSEMBLY (w/ Spare Tire)

    A01GWKI