Click here

HYBRID CONTROL SYSTEM, Diagnostic DTC:P0A10-263

Click here
Click here Click here
DTC Code DTC Name
P0A10-263 DC / DC Converter Status Circuit High Input
Click here

DESCRIPTION

Refer to the description for DTC P0A09-265 (Click here).

DTC No. INF Code DTC Detection Condition Trouble Area
P0A10 263 Short to +B in the hybrid vehicle converter (DC/DC converter) NODD signal line

  • Wire harness or connector

  • Hybrid vehicle converter

  • Hybrid vehicle control ECU
Click here

WIRING DIAGRAM

Refer to the wiring diagram for DTC P0A09-265 (Click here).

Click here

INSPECTION PROCEDURE

CAUTION:

  • Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

  • After disconnecting the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work.

Tip:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.

Click here

PROCEDURE


  1. Click here

    CHECK DTC OUTPUT (HV)


    1. Connect the intelligent tester to the DLC3.

    2. Turn the power switch on (IG).

    3. Select the following menu items: Powertrain / Hybrid Control / Trouble Codes.

    4. Check if DTCs are output.

      Result
      Result Proceed to
      P0A10-263 only is output. A
      P0A10-263 and other DTCs are output. B

  2. Click here

    CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 2 BATTERY PACK WIRE CONNECTOR)


    1. Turn the power switch off.

    2. A01H29WE02

      Disconnect the No. 2 battery pack wire connector (Click here).

    3. Turn the power switch on (IG).

    4. A01GXOME06

      Measure the voltage according to the value(s) in the table below.

      Tip:

      Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      nS1-14 (NODD) - Body ground Power switch on (IG) Below 1 V

  3. Click here

    CHECK HARNESS AND CONNECTOR (NO. 2 BATTERY PACK WIRE CONNECTOR - HYBRID VEHICLE CONVERTER)

    CAUTION:

    Be sure to wear insulated gloves.


    1. Turn the power switch off.

    2. Remove the service plug grip (Click here).

      Note:

      After removing the service plug grip, do not turn the power switch on (READY) unless instructed by the repair manual because this may cause a malfunction.

    3. A01GWIQ

      Disconnect the low voltage connector from the hybrid vehicle converter.

      Tip:

      For the removal and installation procedures related to the low voltage connector of the hybrid vehicle converter, (Click here).

    4. A01GZC6

      Connect the 2 floor wires to the luggage room junction block assembly.

    5. Insulate the AMD terminal of the removed wire with insulating tape to prevent a short to body ground.

    6. Turn the power switch on (IG).

    7. A01GX33E03

      Measure the voltage according to the value(s) in the table below.

      Tip:

      Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      nS1-14 (NODD) - Body ground Power switch on (IG) Below 1 V

    8. Turn the power switch off.

    9. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      Tester Connection Switch Condition Specified Condition
      nS1-14 (NODD) - Other terminals Power switch off 10 kΩ or higher

  4. Click here

    CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - NO. 2 BATTERY PACK WIRE CONNECTOR)


    1. Turn the power switch off.

    2. Disconnect connector A76 from the hybrid vehicle control ECU.

    3. Turn the power switch on (IG).

    4. A01H0VYE07

      Measure the voltage according to the value(s) in the table below.

      Tip:

      Turning the power switch on (IG) with the service plug grip removed causes an interlock switch system DTC (P0A0D-350) to be set.

      Standard voltage
      Tester Connection Switch Condition Specified Condition
      A76-26 (NODD) or nS1-14 (NODD) - Body ground Power switch on (IG) Below 1 V

  5. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  6. Click here

    REPLACE HV CONVERTERClick here

  7. Click here

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  8. Click here

    REPLACE HYBRID VEHICLE CONTROL ECUClick here

  9. Click here

    GO TO DTC CHARTClick here