ENTRY AND START SYSTEM DATA LIST / ACTIVE TEST


  1. READ DATA LIST

    Tech Tips

    Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


    1. Warm up the engine.

    2. Turn the power switch OFF.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the power switch ON (IG).

    5. Turn the tester on.

    6. Enter the following menus: Body / (desired system) / Data List.

    7. According to the display on tester, read the "Data List".

      Main Body
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      ACC SW Power switch ON (ACC)/ON or OFF

      ON: Power switch is ON (ACC)

      OFF: Power switch is OFF

      		 -
      IG SW Power switch ON (IG)/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF

      		 -
      Stop Light SW Stop light switch/ON or OFF

      ON: Brake pedal is depressed

      OFF: Brake pedal is released

      		 -
      Start Switch1 Start switch 1/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF

      		 -
      Start Switch2 Start switch 2/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF

      		 -
      Steering Unlock Switch Steering lock condition/ON or OFF

      ON: Steering is unlocked

      OFF: Steering is locked

      		 -
      Shift P Signal Shift P position signal/ON or OFF

      ON: Shift lever in P

      OFF: Shift lever not in P

      		 -
      Vehicle Speed Signal Vehicle speed signal/STOP or RUN

      STOP: Vehicle is stopped

      RUN: Vehicle is running

      		 -
      IG1 Relay Monitor(Outside) D-IG1-1 relay outer relay monitor/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF

      		 -
      IG2 Relay Monitor(Outside) Ignition relay No. 2 (IG2) outer relay monitor/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF

      		 -
      IG1 Relay Monitor(Inside) D-IG1-1 relay inner relay monitor/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF

      		 -
      IG2 Relay Monitor(Inside) Ignition relay No. 2 (IG2) inner relay monitor/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF

      		 -
      ACC Relay Monitor D-ACC relay monitor/ON or OFF

      ON: Power switch is ON (ACC)

      OFF: Power switch is OFF

      		 -
      Latch Circuit Latch circuit/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF, ON (ACC)

      		 -
      Starter Request Signal Hybrid control system start request signal/ON or OFF

      ON: STSW signal is ON

      OFF: STSW signal is OFF

      		 -
      Power Supply Condition Power supply condition/ALL OFF, ACC ON, IG2 ON, ST ON

      ALL OFF: All relays are OFF

      ACC ON: D-ACC relay is ON

      IG2 ON: Ignition relay No. 2 (IG2) is ON

      ST ON: STSW signal is ON

      		 -
      Ready Signal Hybrid control system start request signal monitor/ON or OFF

      ON: System is ON (READY)

      OFF: System is OFF

      		 Power switch pressed and held with shift lever in P
      Entry&Start
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Ignition Switch Power switch/ON or OFF

      ON: Power switch is ON (IG)

      OFF: Power switch is OFF

      		 -
      Unmatched Vehicle-ID Key number/YES or NO

      YES: Key number matches

      NO: Key number differs

      		 -
      No Response Response/YES or NO

      YES: Response

      NO: No response

      		 -
      Unmatch Code or Form Code format/YES or NO

      YES: Code format matches

      NO: Code format differs

      		 -
      Key Low Battery Key battery conditions/ON or OFF

      ON: Battery is depleted

      OFF: Battery is not depleted

      		 -
      #Codes Number of diagnosis codes - -
      ID Code Difference(Resp) ID code/YES or NO

      YES: ID code matches

      NO: ID code differs

      		 -
      C Code Difference Challenge code/YES or NO

      YES: Challenge code matches

      NO: Challenge code differs

      		 -
      S Code Check S code certification result/NG or OK

      OK: S code certification result is normal

      NG: S code certification result is abnormal

      		 -
      L Code Check L code certification result/NG or OK

      OK: L code certification result is normal

      NG: L code certification result is abnormal

      		 -
      Ignition Available Area Key area where hybrid control system can be operated/ALL or FRONT

      All: All areas

      Front: Front only

      		 -

  2. PERFORM ACTIVE TEST

    Tech Tips

    Using the intelligent tester to perform the Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


    1. Warm up the engine.

    2. Turn the power switch OFF.

    3. Connect the intelligent tester to the DLC3.

    4. Turn the power switch ON (IG).

    5. Turn the tester on.

    6. Enter the following menus: Body / (desired system) / Active Test.

    7. According to the display on tester, perform the "Active Test".

      Main Body
      Tester Display Test Part Control Range Diagnostic Note
      Indicator for Lighting Indicator illumination ON/OFF -
      Indicator Condition Indicator light illumination pattern Green/Amber/No Sig -
      P Supply for Steering Lock Steering lock ECU power supply ON/OFF -
      Entry&Start
      Tester Display Test Part Control Range Diagnostic Note
      Fr-Seat Inside Transmitter Indoor key antenna (for front) ON / OFF -
      Rr-Seat Inside Transmitter Indoor key antenna (for rear1) ON / OFF -
      Inside Trunk/Backdoor Transmitter Indoor key antenna (for rear2) ON / OFF -
      Outside Trunk/Backdoor Transmitter Electrical key antenna ON / OFF -