POWER DOOR LOCK CONTROL SYSTEM OPERATION CHECK


  1. CHECK POWER DOOR LOCK OPERATION

    Note

    The operation check below is based on the non-customized initial condition of the vehicle.


    1. Check the basic function.


      1. Check that all doors lock when the door control switch (for manual operation) is turned to LOCK and all doors unlock when turned to UNLOCK.

      2. Check that all doors lock when the driver side door lock key cylinder is turned to LOCK using the key.

      3. Check that only the driver side door unlocks when turned to UNLOCK once again within 3 seconds using the key (2-step unlocking function).*

        Tech Tips

        *: Only when 2-step unlocking function is set to ON (except Europe and China).

    2. Check the key lock-in prevention function.

      Note

      In order to prevent the key from being locked in, the inspection should be made with the driver side door glass open.


      1. Turn the power switch ON (IG or ACC).

      2. With the driver side door open, check that all doors unlock immediately after the door lock knob for the driver side door is locked.

      3. With the driver side door open, check that all doors unlock immediately after the door control switch (for manual operation) is turned to LOCK.

      4. With the driver side door open, lock the driver side door lock knob and hold it for 2 seconds or more, and then close the driver side door. Then check that all doors unlock.

    3. Check the security function.


      1. Close all doors with the driver side door glass open so that the door control switch can be operated from outside the vehicle.

      2. Remove the key from the inside of the vehicle, open the driver side door and then close and lock the door without using the key. Then, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.

      3. Remove the key from the inside of the vehicle, then close and lock the driver side door with the key operation. Under this condition, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.

      4. Remove the key from the inside of the vehicle, close the driver side door and lock the door with the wireless door lock operation. Then, check that all doors do not unlock when the door control switch (for manual operation) is turned to UNLOCK from outside the vehicle.

        Tech Tips

        Check that the security function is canceled under the following conditions:


        • The power switch is turned ON (IG).

        • The driver side door is unlocked using the key.

        • The door control switch (for manual operation) is turned to UNLOCK after the door lock knob is unlocked manually.

        • The doors are unlocked by wireless operation.

    4. Check the illumination function.


      1. Set the map light switch to the DOOR position.

      2. With all the doors locked, check that all doors unlock when the driver side door lock cylinder is turned to UNLOCK using the key and that the map light turns on.

      3. Check that the map light turns off in approximately 15 seconds after the doors have not been opened.

    5. Check the speed-sensitive automatic door lock function.


      1. When a door is unlocked and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that all doors automatically lock a total of 2 times (automatic door lock).

      2. When a door lock knob is unlocked and the vehicle is driven at approximately 20 km/h (12 mph) or more, check that all doors automatically lock a total of 2 times (repeat function).

    6. Check the automatic locking function interlocked with the shift lever.


      1. When the power switch is ON (READY) and the shift lever is moved from P to a position other than P, check that all doors lock automatically.

        Tech Tips


        • The default setting of the automatic locking function interlocked with the shift lever is OFF. If desired, it must be set ON through customization.

        • Automatic locking operation is disabled when the crash detection sensor (built-in center airbag sensor) unlocking system has a malfunction.

  2. CHECK DOUBLE LOCK FUNCTION

    Note

    Never activate the double locking system when someone is inside the vehicle. The doors cannot be opened from the inside of the vehicle. If the doors are locked accidentally, press the transmitter's UNLOCK switch.


    1. Check that the double locking system is set.


      1. Open all the windows.

      2. Turn the power switch OFF.

      3. Open and close the driver side door, and make sure that all doors including the luggage compartment door are closed securely.

      4. Press the transmitter LOCK switch twice within 5 seconds, and check that the hazard warning lights flash once at this time as an answer back.

      5. Try to unlock all doors with the inside handle of the vehicle, and check that none of the doors unlock.

        Note


        • The double locking system cannot be set without using the transmitter.

        • The double locking system is not applicable to the luggage compartment door.

    2. Check that the double locking system is canceled.


      1. Press the transmitter UNLOCK switch while the double locking system is set, and check that the hazard warning lights flash twice at this time to show that the system is canceled.

      2. Check that the doors can be opened both by the inside handle and the outside handle.

        Tech Tips

        If the battery of the transmitter is depleted, only the driver side door can be opened using the key. However, the theft deterrent system still remains on. The theft alarm will sound when the door is opened without using the transmitter.