ENTRY AND START SYSTEM Front Passenger Side Door Entry Lock and Unlock Functions do not Operate

DESCRIPTION

When the front passenger door entry lock and unlock functions do not operate, one of the following may be malfunctioning: 1) power door lock system, 2) front passenger side door electrical key oscillator, or 3) certification ECU.

WIRING DIAGRAM

A01GXR8E15
A01GXR8E20

INSPECTION PROCEDURE

Note

Before performing the inspection, check that there are no problems related to the "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the master switch assembly's door control switch is operated, check that the locked doors unlock Click here.

      OK
      Locked doors unlock.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)


    1. Using the intelligent tester, read the Data List Click here.

      Passenger Door
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Lock Position SW Front passenger side door lock position switch signal / ON or OFF

      ON: Front passenger side door is unlocked

      OFF: Front passenger side door is locked

      		 -
      OK
      On intelligent tester screen, item changes between ON and OFF according to above chart.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (ENTRY SENSOR, OUTSIDE HANDLE TRIGGER SW)


    1. Using the intelligent tester read the Data List Click here.

      Passenger Door
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Entry Sensor Front passenger side door touch sensor / ON or OFF

      ON: Front passenger side door sensor is touched

      OFF: Front passenger side door sensor is not touched

      		 -
      Outside Handle Trigger SW Front passenger side door outside handle lock switch / ON or OFF

      ON: Front passenger side door outside handle lock switch is pushed

      OFF: Front passenger side door outside handle lock switch is not pushed

      		 -

    NG

    CHECK FRONT DOOR ECU Click here

    OK

  4. CHECK WAVE ENVIRONMENT


    1. A01GXM7E05

      Bring the electrical key transmitter near the front passenger door outside handle, and perform a front passenger door entry lock and unlock operation check.

      Note

      If the key is brought within 0.2 m (0.656 ft.) of the door handle, communication is not possible.

      Tech Tips


      • When the electrical key transmitter is brought near the front passenger door outside handle, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the inspection result is that the operation check is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      • On opposite side for RHD vehicle.

      Result
      Result Proceed to
      Operation check fails A
      Operation check is normal B

    B

    AFFECTED BY WAVE INTERFERENCE

    A

  5. KEY DIAGNOSTIC MODE


    1. A01GXM7E06

      Diagnostic mode inspection door electrical key oscillator


      1. Connect the intelligent tester to the DLC3.

      2. Turn the power switch ON (IG).

      3. Turn the intelligent tester on.

      4. Enter the following menus:

        Select: Body Electrical / Entry&Start / Key Communication Check /Overhead + Passenger Side.

      5. When the electrical key transmitter is in the position shown in the illustration, check that the wireless door lock buzzer sounds*.

        Tech Tips


        • If the buzzer sounds, it can be determined that the front passenger seat outside transmitter is operating normally.

        • *: For Europe and China, the wireless door lock buzzer does not sound.

        • On opposite side for RHD vehicle.

        OK
        Wireless door lock buzzer sounds

    NG

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR) Click here

    OK

    END (CERTIFICATION ECU IS DEFECTIVE)

  6. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - DOOR ELECTRICAL KEY OSCILLATOR)

    A01GZFZE20

    1. Disconnect the L15 ECU connector.

    2. Disconnect the N18*1 or N20*2 oscillator connector.

      Tech Tips


      • *1: for LHD

      • *2: for RHD

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LHD
      Tester Connection Condition Specified Condition
      L15-36 (CG2B) - N18-5 (CLGB) Always Below 1 Ω
      L15-35 (CLG2) - N18-10 (CLG) Always Below 1 Ω
      L15-36 (CG2B) or N18-5 (CLGB) - Body ground Always 10 kΩ or higher
      L15-35 (CLG2) or N18-10 (CLG) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      L15-36 (CG2B) - N20-5 (CLGB) Always Below 1 Ω
      L15-35 (CLG2) - N20-10 (CLG) Always Below 1 Ω
      L15-36 (CG2B) or N20-5 (CLGB) - Body ground Always 10 kΩ or higher
      L15-35 (CLG2) or N20-10 (CLG) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK HARNESS AND CONNECTOR (FRONT DOOR ECU - DOOR ELECTRICAL KEY OSCILLATOR)

    A01H18XE94

    Tech Tips


    • *1: for LHD

    • *2: for RHD


    1. Disconnect the N1*1 or N10*2 ECU connector.

    2. Disconnect the N18*1 or N20*2 oscillator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LHD
      Tester Connection Condition Specified Condition
      N1-15 (SEL) - N18-4 (SEL) Always Below 1 Ω
      N18-4 (SEL) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      N10-15 (SEL) - N20-4 (SEL) Always Below 1 Ω
      N20-4 (SEL) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  8. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)

    A01GXQXE40

    Tech Tips


    • *1: for LHD

    • *2: for RHD


    1. Disconnect the N18*1 or N20*2 oscillator connector.

    2. Disconnect the N19*1 or N21*2 handle connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LHD
      Tester Connection Condition Specified Condition
      N18-3 (ANT3) - N19-5 (ANT3) Always Below 1 Ω
      N18-8 (ANT4) - N19-2 (ANT4) Always Below 1 Ω
      N18-3 (ANT3) - Body ground Always 10 kΩ or higher
      N18-8 (ANT4) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      N20-3 (ANT3) - N21-5 (ANT3) Always Below 1 Ω
      N20-8 (ANT4) - N21-2 (ANT4) Always Below 1 Ω
      N20-3 (ANT3) - Body ground Always 10 kΩ or higher
      N20-8 (ANT4) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  9. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)


    1. Replace the door electrical key oscillator with a new one or normally functioning one Click here.

    2. Check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION) Click here

    OK

    END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

  10. CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION)


    1. Replace the front door outside handle RH*1 or LH*2 with a new one or normally functioning one Click here.

      Tech Tips


      • *1: for LHD

      • *2: for RHD

    2. check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    CHECK FRONT DOOR ECU (OPERATION) Click here

    OK

    END (FRONT DOOR OUTSIDE HANDLE IS DEFECTIVE)

  11. CHECK FRONT DOOR ECU (OPERATION)


    1. Replace the front door ECU RH*1 or LH*2 with a new one or normally functioning one Click here.

      Tech Tips


      • *1: for LHD

      • *2: for RHD

    2. Check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    REPLACE CERTIFICATION ECU

    OK

    END (FRONT DOOR ECU IS DEFECTIVE)

  12. CHECK FRONT DOOR ECU

    A01H1E2E14

    1. Measure the voltage according to the value(s) in the table below.

      Standard voltage
      for LHD
      Tester Connection Condition Specified Condition
      N1-12 (OSCB) - N1-19 (OSCE) Always 11 to 14 V
      for RHD
      Tester Connection Condition Specified Condition
      N10-12 (OSCB) - N10-19 (OSCE) Always 11 to 14 V

    NG

    REPLACE FRONT DOOR ECU Click here

    OK

  13. CHECK HARNESS AND CONNECTOR (FRONT DOOR ECU - DOOR ELECTRICAL KEY OSCILLATOR)

    A01H18XE95

    Tech Tips


    • *1: for LHD

    • *2: for RHD


    1. Disconnect the N1*1 or N10*2 ECU connector.

    2. Disconnect the N18*1 or N20*2 oscillator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LHD
      Tester Connection Condition Specified Condition
      N1-12 (OSCB) - N18-1 (B) Always Below 1 Ω
      N1-14 (SENS) - N18-6 (SENS) Always Below 1 Ω
      N1-19 (OSCE) - N18-7 (GND) Always Below 1 Ω
      N18-1 (B) - Body ground Always 10 kΩ or higher
      N18-6 (SENS) - Body ground Always 10 kΩ or higher
      N18-7 (GND) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      N10-12 (OSCB) - N20-1 (B) Always Below 1 Ω
      N10-14 (SENS) - N20-6 (SENS) Always Below 1 Ω
      N10-19 (OSCE) - N20-7 (GND) Always Below 1 Ω
      N20-1 (B) - Body ground Always 10 kΩ or higher
      N20-6 (SENS) - Body ground Always 10 kΩ or higher
      N20-7 (GND) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)

    A01GXQXE41

    Tech Tips


    • *1: for LHD

    • *2: for RHD


    1. Disconnect the N18*1 or N20*2 oscillator connector.

    2. Disconnect the N19*1 or N21*2 handle connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LHD
      Tester Connection Condition Specified Condition
      N18-2 (SGT4) - N19-6 (SGT3) Always Below 1 Ω
      N18-9 (TRG-) - N19-1 (TRG-) Always Below 1 Ω
      N18-2 (SGT4) - Body ground Always 10 kΩ or higher
      N18-9 (TRG-) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      N20-2 (SGT4) - N21-6 (SGT3) Always Below 1 Ω
      N20-9 (TRG-) - N21-1 (TRG-) Always Below 1 Ω
      N20-2 (SGT4) - Body ground Always 10 kΩ or higher
      N20-9 (TRG-) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  15. CHECK HARNESS AND CONNECTOR (FRONT DOOR ECU - FRONT DOOR OUTSIDE HANDLE)

    A01GYHTE75

    Tech Tips


    • *1: for LHD

    • *2: for RHD


    1. Disconnect the N1*1 or N10*2 ECU connector.

    2. Disconnect the N19*1 or N21*2 handle connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LHD
      Tester Connection Condition Specified Condition
      N1-20 (TRG+) - N19-3 (TRG+) Always Below 1 Ω
      N19-3 (TRG+) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      N10-20 (TRG+) - N21-3 (TRG+) Always Below 1 Ω
      N21-3 (TRG+) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  16. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)


    1. Replace the door electrical key oscillator with a new one or normally functioning one Click here.

    2. Check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION) Click here

    OK

    END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

  17. CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION)


    1. Replace the front door outside handle RH*1 or LH*2 with a new one or normally functioning one Click here.

      Tech Tips


      • *1: for LHD

      • *2: for RHD

    2. Check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    REPLACE FRONT DOOR ECU Click here

    OK

    END (FRONT DOOR OUTSIDE HANDLE IS DEFECTIVE)