ENTRY AND START SYSTEM Front Passenger Side Door Entry Unlock Function does not Operate

DESCRIPTION

If the front passenger door entry unlock function does not operate but the entry lock operation operates, the communication line between the vehicle and electrical key transmitter is normal. Either of the following may have occurred: 1) the door outside handle touch sensor is malfunctioning; or 2) the front door ECU RH receives the door outside handle touch sensor ON signal, but is unable to send the signal to the certification ECU through CAN communication.

WIRING DIAGRAM

Refer to Front Passenger Side Door Entry Lock and Unlock Functions do not Operate Click here.

INSPECTION PROCEDURE

Note


  • Before performing the inspection, check that there are no problems related to the "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".

PROCEDURE


  1. CHECK POWER DOOR LOCK OPERATION


    1. When the master switch's door control switch is operated, check that the locked doors unlock Click here.

      OK
      Locked doors unlock.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

    OK

  2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)


    1. Using the intelligent tester, read the Data List Click here.

      Passenger Door
      Tester Display Measurement Item/Range Normal Condition Diagnostic Note
      Lock Position SW Front passenger side door lock position switch signal / ON or OFF

      ON: Front passenger side door is unlocked

      OFF: Front passenger side door is locked

      		 -
      OK
      On intelligent tester screen, item changes between ON and OFF according to above chart.

    NG

    GO TO POWER DOOR LOCK CONTROL SYSTEM (Proceed to Only Passenger Door LOCK/UNLOCK Functions do not Operate) Click here

    OK

  3. READ VALUE USING INTELLIGENT TESTER (ENTRY SENSOR)


    1. Using the intelligent tester read the Data List Click here.

      Passenger Door
      Tester Display Measurement Item/Display Normal Condition Diagnostic Note
      Entry Sensor Front passenger side door touch sensor / ON or OFF

      ON: Front passenger side door sensor is touched

      OFF: Front passenger side door sensor is not touched

      		 -
      OK
      On intelligent tester screen, item changes between ON and OFF according to above chart.

    NG

    CHECK HARNESS AND CONNECTOR (FRONT DOOR ECU - DOOR ELECTRICAL KEY OSCILLATOR) Click here

    OK

  4. CHECK FRONT DOOR ECU (OPERATION)


    1. Replace the front door ECU RH*1 or LH*2 with a new one or normally functioning one Click here.

      Tech Tips


      • *1: for LHD

      • *2: for RHD

    2. Check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    REPLACE CERTIFICATION ECU

    OK

    END (FRONT DOOR ECU RH IS DEFECTIVE)

  5. CHECK HARNESS AND CONNECTOR (FRONT DOOR ECU - DOOR ELECTRICAL KEY OSCILLATOR)

    A01H18XE87

    1. Disconnect the N1 or N10 ECU connector.

    2. Disconnect the N18 or N20 oscillator connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LHD
      Tester Connection Condition Specified Condition
      N1-15 (SEL) - N18-4 (SEL) Always Below 1 Ω
      N1-15 (SEL) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      N10-15 (SEL) - N20-4 (SEL) Always Below 1 Ω
      N10-15 (SEL) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (DOOR ELECTRICAL KEY OSCILLATOR - FRONT DOOR OUTSIDE HANDLE)

    A01GXQXE29

    1. Disconnect the N18 or N20 oscillator connector.

    2. Disconnect the N19 or N21 handle connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance
      for LHD
      Tester Connection Condition Specified Condition
      N18-2 (SGT4) - N19-6 (SGT3) Always Below 1 Ω
      N18-2 (SGT4) - Body ground Always 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      N20-2 (SGT4) - N21-6 (SGT3) Always Below 1 Ω
      N20-2 (SGT4) - Body ground Always 10 kΩ or higher

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)


    1. Replace the door electrical key oscillator with a new one or normally functioning one Click here.

    2. Check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION) Click here

    OK

    END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)

  8. CHECK FRONT DOOR OUTSIDE HANDLE (OPERATION)


    1. Replace the front door outside handle RH*1 or LH*2 with a new one or normally functioning one Click here.

      Tech Tips


      • *1: for LHD

      • *2: for RHD

    2. Check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    CHECK FRONT DOOR ECU (OPERATION) Click here

    OK

    END (FRONT DOOR OUTSIDE HANDLE IS DEFECTIVE)

  9. CHECK FRONT DOOR ECU (OPERATION)


    1. Replace the front door ECU RH*1 or LH*2 with a new one or normally functioning one Click here.

      Tech Tips


      • *1: for LHD

      • *2: for RHD

    2. Check that the entry function operates normally Click here.

      OK
      Operates normally

    NG

    REPLACE CERTIFICATION ECU

    OK

    END (FRONT DOOR ECU RH IS DEFECTIVE)