CYLINDER HEAD REPLACEMENT

Tech Tips

When viewed from the rear of the engine assembly, Bank 1 is on the left side and Bank 2 is on the right side.


  1. REPLACE INTAKE VALVE GUIDE BUSH


    1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    2. Place the cylinder head on wooden blocks.

    3. A01GWCCE02

      Using SST and a hammer, tap out the valve guide bush.

      SST
      09201-10000   ( 09201-01050 )
      09950-70010   ( 09951-07100 )
    4. A01H0BO

      Using a caliper gauge, measure the bush bore diameter of the cylinder head side.

      Standard cylinder bore diameter
      10.285 to 10.306 mm (0.405 to 0.406 in.)

      If the bush bore diameter of the cylinder head is between 10.285 to 10.306 mm (0.405 to 0.406 in.), proceed to the next step.

      If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.

    5. Select a new guide bush (STD or O/S 0.05), and measure its diameter.

    6. Machine the bush bore diameter of the cylinder head side to the diameter of the selected guide bush.

      Bush bore diameter
      Bush Size Specified Condition
      STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
      O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)
      Standard bush length
      41.3 to 41.7 mm (1.63 to 1.64 in.)

    7. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    8. A01H22YE01

      Using SST and a hammer, tap the guide bush to the specified protrusion height.

      SST
      09201-10000   ( 09201-01050 )
      09950-70010   ( 09951-07100 )
      Standard protrusion height
      14.3 to 14.7 mm (0.563 to 0.579 in.)
    9. A01GWEA

      Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.

  2. REPLACE EXHAUST VALVE GUIDE BUSH


    1. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    2. Place the cylinder head on wooden blocks.

    3. A01H0RZE02

      Using SST and a hammer, tap out the valve guide bush.

      SST
      09201-10000   ( 09201-01050 )
      09950-70010   ( 09951-07100 )
    4. A01GWJ4

      Using a caliper gauge, measure the bush bore diameter of the cylinder head.

      Standard cylinder bore diameter
      10.285 to 10.306 mm (0.405 to 0.406 in.)

      If the bush bore diameter of the cylinder head is between 10.285 to 10.306 mm (0.405 to 0.406 in.), proceed to the next step.

      If the bush bore diameter of the cylinder head is 10.356 mm (0.408 in.) or more, replace the cylinder head.

    5. Select a new guide bush (STD or O/S 0.05), and measure its diameter.

    6. Machine the bush bore diameter of the cylinder head side to the diameter of the selected guide bush.

      Bush bore diameter
      Bush Size Specified Condition
      STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
      O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)
      Standard bush length
      46.8 to 47.2 mm (1.84 to 1.86 in.)

    7. Heat the cylinder head to approximately 80 to 100°C (176 to 212°F).

    8. A01H1VNE01

      Using SST and a hammer, tap in the guide bush to the specified protrusion height.

      SST
      09201-10000   ( 09201-01050 )
      09950-70010   ( 09951-07100 )
      Standard protrusion height
      14.3 to 14.7 mm (0.563 to 0.579 in.)
    9. A01H1LG

      Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard specified clearance between the guide bush and valve stem.

  3. REPLACE SPARK PLUG TUBE

    A01H2C9E01

    Tech Tips

    When using a new cylinder head, the spark plug tubes must be replaced.


    1. Remove the spark plug tube.

    2. Apply adhesive to the end of a new spark plug tube.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent
      Standard seal diameter
      15 mm (0.591 in.)

      Note


      • Install the spark plug tube within 3 minutes after applying adhesive.

      • Be careful not to deform the spark plug tube.

      • Be careful not to expose the seal to coolant for at least 1 hour after installing it.

    3. A01H0YFE01

      Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.

      Standard protrusion height
      66.6 to 67.6 mm (2.62 to 2.66 in.)

      Note

      To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.

  4. REPLACE RING PIN

    Note

    It is not necessary to remove the ring pin unless it is being replaced.


    1. Remove the ring pins.

    2. Using a plastic-faced hammer, tap in new ring pins until they pin stop.

      Standard protrusion
      Item Specified Condition
      Ring pin A 5.5 to 6.5 mm (0.217 to 0.256 in.)
      Ring pin B 3.5 to 6.5 mm (0.138 to 0.256 in.)
      A01H1OCE01